Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
I have compiled asset tracker example and it worked on 0.8.2 version of board but not on 0.8.5 board.
1) Is there anything which should be made differently in software for...
Hi, I'm trying to measure the current of my nRF9160 DK (PCA10090 v0.8.2) and have some problems. In respect to the following thread (https://devzone.nordicsemi.com/f/nordic...
Hello. Project im developing requires low power wireless encoder. NRF52832 is a really impressive chip that handles everything i need within 40uA. But I've got problem with...
hi, we delevoppe a card with a module which is use your nRF52832 IC. I check in your document information relative to IO hardware, but i didn't find any information concerning...
I am writing some code for a customer using the nrf52840.
The Softdevice asserts immediately after a call to nrf_fstorage_write().
The write address is OK, alignment...
whenever I use nrf connect desktop app in my Linux system for power profilling.
The power profiling kit doesn't start and keeps on giving the same error
There are similar...
Hello team, I'm working on system development using Mesh SDK and I have some questions so please let me know. ############### Development environment IDE : Segger Embedded...
I was able to create 2 times, Timer 1 and Timer 2.
They work when they run separately, but one stops when I try to use both of them.
I need simultaneously running two...
Please confirm the following is correct for nRF52840 (per PS v1.1)
1. The firmware doesn't have to enable internal pull-up when the pin reset is configured (it's done automatically...
Hi,
I am developing a solution with zigbee (nRF52840).
I want some end device is joined to specific router.
In the documents, if end device find more than one router...
Hi, Everyone.
I'm trying to connect nRF52 DK Board to J-link base tool.
But I can't connect.
Wires between nRF52 B/D and J-link base tool are conneted below.
nRF52...
Hi,
I am new in this area. I wanted to use the detect "signal" but it doesn't work as protected. This is my main :
I just try to detect when the detect signal is HIGH...
Hello,
i tried the getting started procedure with the NRF9160DK demo board but I cannot finish the whole procedure.
After activating the iBasis eSIM, I turn on the...
It's may be strange enough, but i can't see the clear answer on this question. What is the limitations for pin function maping? I need to understand which pins i can use for...
Hi,
I am surveying the zigbee example for my project.
In my project, coordinator has to permit or reject certain end device/router.
I have searched following articles...
