I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
I'm using SDK 12.3.0, and changed the TX_PIN to 30, RX_PIN to 5, flow control is set to false, bitrate no change(19200).After I programmed the firmware to my custom board...
I'm trying to test my nRF7002DK with aws_iot sample to see how it works. I'm following this guide however it fails during build configuration & never builds whatsoever. I...
Hi,
I have tested my BLE code and UART code separately, and both worked correctly during individual testing.
However, when integrating both, I encountered an issue with...
I see other posts stating that the nRF Connect For Desktop 'Toolchain Manager' requires an internet connection to download the nRF Connect SDK versions. I'm thinking of the...
I need to connect a device to an nRF5340 SPI port without creating a custom driver. I'm tempted to use the nrfx_spim driver directly, but I'm trying to do it with Zephyr and...
Hi,
I am migrating from nCS v2.6.1 to v2.9.0, my workspace builds fine on v2.6.1 But on v2.9.0 I am getting the below error:
This is being generated as my main.c has...
Hi
i want to generate security key with the combination of time and private key.can i acheive it in NRF..mainly in NRF52833?
i have a ref code in this repo.. here can...
Hi,
My goal is to primarily save the audio being generated by the Headset device in the LE Audio samples. I have established Bidirectional stream between the Headset and...
I had received a lot of support in: Replacing RS485 link with NRF24L01+ .
At the moment I have 95% proyect working OK but in one operation mode of my program, after some...
it will take about 25uA~ 28uA.
when I remove R18 R19, set io to input with pullup, it will take about 10uA,
&button1 {
gpios = <&gpio0 5 ( GPIO_ACTIVE_LOW | GPIO_PULL_UP...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi Nordic Team I am working on a BLE application using the nRF5 SDK 17.1.0 with Peer Manager configured for Security Mode 1 Level 4 . I am encountering an issue related to...
Hi,
We found a very strange problem when designing a product using nrf5340: The equipment is coated with a layer of UV tri-proof paint on the chip of nRF5340 and the peripheral...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
