Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
I want to make serial connection in between an nRF52833 and a LPC1752.
When I use the UART in a firmware without using the SoftDevice for Mesh 4.0.1 , everything is working...
Hi,
I am using a Linux Host to communicate with my nRF52840 as a USB CDC ACM device. As a test, I ran minicom and was able to transfer bytes to my Nordic app successfully...
Gentlemen:
I'm new to Nordic processors, but I have implemented projects with Silabs Gecko and ATTiny processors in the past. I'm working on a project for a consumer product...
Hello,
I have installed Embedded Studio and acquired a Nordic license. However the Tools/Options... nRF Connect menu option does not appear. I tried creating a dummy Nordic...
The project for nRF51822 was developed on base of example ble_peripheral ble_app_hrs for pca10028/s130 with an additional vendor specific service with 128-bit UUID for an...
I have a strange problem. We built 100 custom boards. I've only checked about 50 boards so far. 47 boards work properly. 3 do not.
We used secure_bootloader_uart_pca10056...
Hi support team
One of our customer ask if it's possible to transfer a file system(LittleFS,refer: https://github.com/ARMmbed/littlefs ) to our Soc?? If not, are there some...
I am new to BLE and I am exploring Introduction to service. However I am stuck with Step 1 and Step 2. Is Step 1: static ble_os_t m_our_service; (to declare a service) and...
I have a device with no OS on it that talks serial through a UART to a nRF53840. I need to be able to update the nRF53840's firmware across the serial link, but since I don...
Hello, I am working on the BMD-300 Series Evaluation Kit with nrf52832 microcontroller and I tried accessing the serial number of my nrf52832, with these functions:
m_device_id1...
One doubt, if a node gets reset or disconnected , due to power failure in openthead cli mesh, dose it need to get configured again to join the mesh or will it connect to mesh...
First, by "Custom Protocol" I just mean that I need to directly access the radio to transmit or receive single packets occasionally. The literature appears to indicate that...
Hi, We flashed an ncs v1.3.0-rc1 build onto a 5340 DK network core, and ever since then the UART is not sending any data to our PC. We have connected RxD and TxD to pins P0...
I've seen a few discussions on C++ support. It's frustrating I can't contribute to the conversation - I'm not sure if that's because my account is too new, or if comments...
Good day, support!
I have a couple of questions regarding the mandatory services of the nRF52840 dongle.
1) How to add characteristics to the mandatory services 0x1800...
