Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hi,
I am trying to find RSSI of the value of the nearest device also I need the Device name, address of those devices. I got the RSSI value but some problem in D evice name...
I'm upgrading a project from SDK 15 to SDK 16. Previously in my gap parameters init I had this code
This works fine for seeing the peripheral and operating it as a UART...
I wasn't sure which product to put in. I am looking for a BLE discovery tool for EEG devices -- particularly the Muse 2 Headband. Which of Nordic's software should I use for...
Hi,
In our project, we are using a small RTOS to switch between simple tasks and set MPU. We would like to run all task in unprivileged mode, but some Nordic SDK libraries...
Hi everyone,
I have written a code that sends data over BLE notifications (IMU data). It works great so far and now I want to read the analog values from eight force sensors...
Hi everyone,
I have a problem I can't sort out. My program runs fine indefinitely if I set one variable in a function at one point but if I don't do that, the program, or...
Hello,
We have around 700 product in the field based on the Simblee BLE module, which was discontinued 1+ year ago. Application was developed using Simblee's proprietary...
Hello,
I need to develop two applications for nRF51822 using SES version 4.18 (macOS). One is a DFU bootloader. The other is an application based on the ble_app_uart (ble_peripheral...
Hello,
I am trying to run the BLE Thread Dynamic Template example on a nRF52840 dongle. I'm using Segger Embedded Studio to generate an hex file. I flash the hex file to...
Hello,
During testing we found that whenever in system off mode, the CPU wakes from VBUS rising. As expected. We then do a vibration to notify the user the USB cable was...
When integrating nRF Mesh SDK 4.1 with nRF SDK 16 I got an error in runtime.
The call sequence:
mesh_init() -> mesh_stack_init() -> nrf_mesh_init() -> mesh_config_init...
Hi all,
I have really strange behavior with Sesgger SES. I'm working on Linux Kubuntu lastest version.
Segger version is :
SEGGER Embedded Studio for ARM
Release 4...
I am trying to use C++ with an nRF5 board, but I'm running into issues with the MDK, IAR (v8.40.2), and C++. When I try to include "nrfx_gpiote.h" in a .cpp file, I get the...
Hi,
I have a basic setup consisting of a time-slotted transmitter and receiver so that I can experiment with the raw coded and uncoded modes, exploring all the NRF_RADIO...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
