Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
I need help in implementing Monitor Mode Debugging (MMD) using Segger Embedded Studio development. Can you please provide detailed help and explanation please?
Hi Devzone:
After searching through the forum I found out that nrf_fstorage_write can only make 1 to 0. So each write needs an erase operation preceding it.
But erase...
Baseline: CLI example on the 52832 with SDK v15.3
I assume the issue will be some more undocumented fix.
sdk_config.h
main.c from the CLI example (UART backend...
I was previously working on nRF51822 ble beacon, in which codes flash of hex 20006.
But i wanted to flash a code nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\experimental_ble_app_blinky...
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
Hello there, I know that softdevice supports up to 20 connections at the same time, but we need more actually.
If i implement a SPI ram to device, is there any change...
It seems NB-IOT can work on different modes according network operator condition, is there any way via AT command to interrogate the nRF91 to know the "operation mode" and...
Hello,
I just created an application that can count the number of rising edges/events on button presses using the TIMER0 peripheral configured as a COUNTER. So far it is...
I am developing an application for Android and IOS. Faced a problem when try connect nRF Connect as central (on Android) to nRF Connect as peripheral (on IOS)
...
What I need?
I should be able to perform scanning, connecting, disconnecting and accessing service from main() (in a infinite while loop) rather than interrupts. I see that...
Hello,
I'm using SDK16 with the s332-6.1.1 softdevice in ANT mode.
When I request a radio timeslot of 10 ms, that works just fine, but if I do anything longer than approx...
Hello,
we have developed a custom board using the nrf9160 SICA chip and are now modifying the bifravst cat tracker example to suite our needs.
Basicaly, it samples from...
I am trying to get my ublox module to respond to at commands, through the programming of the boron module, which is found in this link, but I don't have much idea of how...
Hi.
I am trying to get mesh DFU working and I keep getting "Failed to upgrade target. Error is: Crashed on start packet" from nrfutil.
When debugging the target I see...
