Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Would a wire-wound inductor work better than a chip inductor for the antenna circuit of NRF52810? I'm using the 32 pin QFN package with the LDO configuration which calls for...
I need to calculate the max number of concurrent connection Central can support given the following
Connection Internval = 7.5ms
Baud Rate per connected peripheral:...
Where can I find this version of hub?
ERROR: Could not find a version that satisfies the requirement hub==2.0 (from -r zephyr/scripts/requirements.txt (line 10)) (from versions...
When nrfutil is installed with python 3, I get an error when generating bootloader settings page. This does not occur with python 2. As python 2 support expires very soon...
Hi.
I am testing MESH by nrf5SDKforMeshv201src and nRF5_SDK_15.0.0_a53641a.
I have a problem.
My project have one of the client and one of the server.
Client transmit...
Hi I had a question to setup the MCP2515 driver in the zephyr project.
We have a custom board for the decawave DWM1001 module, which uses a nRF52832 chip. They have a device...
Hello I am using a I2C sensor module and I need to tranmit only address to receive data back, but I dont know how.
Program crashes on line 4.
Thank you for your help...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
When the bluetooth service function is initialized, sd_ble_uuid_vs_add() is called in the ble_dfu_buttonless_init() function in case of an out of memory error. In the ble_nus_init...
Hello, Is there any evaluation kit available for NRF905? I found this one online but DIGIKEY website says its obsolete::
media.digikey.com/.../nRF905-EVKIT_PS_Rev1.0_Jan2004...
Dear Nordic staff and users,
Now I'm trying to confirm that my local LTE operator supports energy saving modes. It went with flying colours with PSM:
at+cereg=5 OK at...
using SEGGER Embedded Studio for ARM V4.30a, I get a problem of Linking with an nRF5_SDK "blinky" examples. See hereunder the error message:
Seem to be a problem of configuration...
Hello,
I can create a zip file with nrfutil pkg generate and there is a bin file in it? I want to make DFU as a bin file only.
I only want to download the firmware as...
Hello,
I have a question about using pins as output. I'm trying to set 2 pins to "1", but cant fully understand how to use pins on port1.
for example: P0.10 (wich works...
