Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
I've written a detailed description of how to program & debug the NRF52832 using open-source tools and the Nordic SDK.
See https://iosoft.blog/arm-gcc-lean-nordic-nrf52...
Hi all
I am working on Bluetooth application using NRF52840 kit. The application is very simple, the device would have about 7 push buttons which when pressed data will...
During testing of SDK for Mesh v3.2.0 I noticed that it's no longer possible to send a request and response using SAR where both models are on the same element. This was possible...
Dear All,
On the NRF52840 AD6 and AD4 are for USB D+ and D-, in the case I have no need to route USB signal can I use these 2 lines for General Purpose I/O especially high...
Hi
I have some questions that need your help.But it seems that there is no answer yet.The following is my questions link.
https://devzone.nordicsemi.com/f/nordic-q-a/52060...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
Hi!
I searched the devzone and there is quite few topics about how the relay is enabled / disabled in the FW... according to https://www.youtube.com/watch?v=r9CvtbCmYQY...
Hi,
I'm unable to hit my break points while using the J-link Lite debugger.
Mostly, after I've attached the debugger and reset, it goes to the correct location
FUNC_NORETURN...
Hi,
I am using the nrf51422 controller and other controller which contains Bluetooth .The nrf51422 Bluetooth is central and other controller Bluetooth is peripheral.I am...
Hi to all,
I am using nRF52832 DK with SDK 15.0 version. My two nRF52 DK damaged while debugging I am a little bit confused why this happening.
When I debugging I used...
Hi,
I need a way to dynamically disable watchdog when I do MMD debugging. I found the old trick, check bit 0 on CoreDebug->DHCSR, does not work any more in MMD. Is that...
I suspect a possible race condition happening during NUS service discoveries. I have two peripherals that are advertising and have DIS, Battery and the NUS service enabled...
Hello,
I have configured max30101 with nrf51 and I want to read the fifo of max30101. The fifo can contain 32 samples and the size of each sample could vary from 3-9 bytes...
I followed the suggestions in https://devzone.nordicsemi.com/f/nordic-q-a/51642/can-t-build-nrf-connect-asset-tracker
But, still having the same issue.
Using tag v1.0...
On one of our products, we are experiencing approximately 4% failures during production. I traced the problem to be caused by function sd_softdevice_enable not returning....
