i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
The USB connector came apart from the nRF9160 development kit soon after a purchase was made from Symmetry Electronics. Would it be possible to have the board replaced...
I have an RTOS application into which I integrated a custom BLE service code. Question is, there isn't any need for a separate thread for handling BLE stuff? I see BLE events...
Hi,
I am trying to use UART APIs in blocking mode to receive data from another controller.
I intend to have a timeout on receiving function so not to stuck if no byte...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I am investigating the data bit and stop bit settings. At that time, I found a page...
Hi !
I try to use VSCode but any examples return same error:
"Linking C executable zephyr\zephyr_prebuilt.elf FAILED: zephyr/zephyr_prebuilt.elf zephyr/zephyr_prebuilt...
Hi,
As the title states, VS code doesn't recognize includes related to Zephyr.
I've walked through the entire setup guide and installed all components using the toolchain...
So I came across an issue while working on developing an app that can update firmware OTA. I was using Nordic Semi - android DFU Library
implementation 'no.nordicsemi.android...
hi，
1.Now I am using Wireshark to capture nrF52840 DK ZigBee packets. I have configured the environment according to the guide. In wireshark, "nRF Sniffer for 802.15.4"...
hi，
we are using52833 QFN40 to test carrier,but the program will loop at as the picture bellow,while it runs well in 52833 QQFN73 in another board, why? Coutl you help me...
Hello,
Our modem consumes a lot of current when we use a simcard from a provider 1 (a MNO), much more that when we use a simcard from another provider 2 (a roaming service...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
Hi
The chip used is nrf52832, the SDK version is a peripheral device v13, and the central device uses v16.
The referenced example is ble_app_multirole_lesc and has been...
Background: SDK 16.0.0, SoftDevice 7.0.1, 1 ble_central connected 6 ble_peripheral, Send an instruction to 6 ble_peripherals every 50 milliseconds, at the same time, the ble_peripheral...
