when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
i have used "BLE_GAP_PHY_AUTO" in scanner code
actually it should scan "phy coded" and "non phy coded" aid values .
but in my case getting i was getting both "phy coded...
I have a project to use NRF52810 to connect the App. When testing it, I found that when it was successfully connected to the NRF Connect tool, it would automatically disconnect...
Hi, Dev Zone.
thanks for help : )
I'm try to porting DK Board's Ble Bonding function to Target Board.
1st_question <- this is my first question links
main problem...
I'm using
SDK : nRF5_SDK_17.0.2
Example Project : ble_app_uart
Soft device :S113
The initial project builds successfully.
My project has requirements for tow...
development tool : Segger Embedded Studio
SDK:nRF5_SDK_17.0.2_d674dde
it always takes long time to build project
build log:
Building ‘blinky_pca10056’ from solution...
Hello all,
I am developing an application from the ble_cgms example on the nrf5_sdk 17 using the Softdevice S132.
I have implemented a gpiote interrupt whenever the state...
Hello,
I just received nRF9160DK(PCA10090, 0.8.3)
I followed nRF9160_DK_Getting_Started_Guide doc.
But, I hare some issue to activate iBasis Sim card.
It keeps...
Hello, I am using the latest version of pc-ble-driver combined with a pca10040 and I am attempting to write large data packets (200 bytes) to a peripheral. I compiled the...
Hi,
I have tested FOTA code in nRF52840 DK and it works perfect but i have custom board build with nrf52840 when i implement the code it doesn't get start
custom board...
I don't have time to learn the massive API for nRF52840 so I am hoping someone can provide a small
snippet of code (and instructions to put on the dongle) to do the following...
Hello
While converting from nRF52832 to nRF52810, we found a problem that the SEGGER compiler returns with the message
section '.init' will not fit in region 'UNPLACED_SECTIONS...
Bluetooth didn't have a standard for transmitting audio using LE until LE Audio was released. And many manufacturers which produced BLE remote controls used Voice Over HID...
In my project, nrf9160 has to send and receive data from the I2C bus from a chip. Everything works fine but unfortunately I have to query the chip by sending a single byte...
Hi,
I'm using nRF52840 DK to construct and test a wireless data transmission system.
The problem is that I need to detect a 2M Hz clock's rising edge using nRF and...
Dear Community,
we are looking into an application where the Gateway (RX) uses the nRF5340 + antenna array and the clients (TX) the nRF52840. The clients are on the market...
