Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
hi eveyone.
I want to trying this example,but i used nrf connect and nrf toolbox doesn't see the DEVICE_NAME.(SDK 16)
please tell me what happened.
by the way.I use...
Hi,
I have some questions regarding errata 136.
I understand that the workaround is to ignore reset reason bits which are not RESETPIN .
However, I don't understand...
Hello,
I am trying to transfer firmware packages in sequence (SD , BL & APP) to iOS device. I am using button less DFU without bonds. iOS device could able to transfer only...
Hello everyone,
I am working with nrf52832 ble_app_uart example project. I added twis i2c slave functionality in this project, and the project is working fine. Whenever...
When I try to increase the CENTRAL_LINK_COUNT to 9 in ble_app_multilink_central example, I got this error NRF_ERROR_CONN_COUNT . Is there a way to increase the max connections...
Hi All,
I have a device configured as i2c master, The device is sending 1024 byte of data to NRF52832 DK continuously in form of 255-bytes packet. But I observed that I...
Hello,
I am trying to get the nrf sniffer working to test the ble connection between my 9160DK board and thingy52 board. Some custom software running on both board and...
Hi all,
I am currently experimenting with the gps sample and I would like to adjust the AGPS data update interval.
As far as I understand, in the gps sample, is set to...
Hi,
we are using nRF52840 in our project, we also set some configuration like below snapshot
Here it comes 185uA, we want to know what is the overall consumption means...
Hi ,
I am working on the nRF52 Dk Kit and running the example code- found on the folder \ble_central_and_peripheral\experimental\ble_app_interactive. This is command line...
As you will see with my simple files I have followed about 3 different tutorials to get to the point I am at. I am trying to replace the included SALSProbe.ino program with...
Hello,
I'm trying to program an nrf52 PCB I created from Arduino and code studio just trying to upload a simple blink but when ever I try to connect any of my ST-link...
Hello
I have defined the SPI pins in the sdk_config of the ble_app_uart example and compiled the code after adding the dependent drivers from spis project as shown in...
Hello,
when writing content onto the CDC-ACM interface of the nrf52840, I sooner or later always end up in a Segmentation fault.
I'm on nRF52840 and using the SDK v16...
I'm using the nRF52840-DK evaluation software from Segger. I want to add NAND Flash support, so I want to add an SPI interface. I have looked at the example in nRF5SDK160098a08e2...
