Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
I enter to bootloader via my app by UART command:
err_code = sd_power_gpregret_clr(0, 0xffffffff);
APP_ERROR_CHECK(err_code);
err_code = sd_power_gpregret_set(0, 0xB1...
I know nothing about bluetooth
like ble_app_uart , uart to where?how to use this uart?
like ble_app_alert_notification, alert? beep? vibrator?
any tutorial of develop...
Hi. I am connecting to and establishing a bond between my Android phone and the nRF52832 board using the s132 SoftDevice. I'm in a situation where the Android phone has a...
Hello,
I have the following setup:
A Raspberry Pi 3 B and a nRF52840 Development Kit acting as a Border Router as described here
Another nRF52840 Development Kit...
Hi there,
I'm trying to run the beacon s130 pca20006 example on a custom board. There are 2 main differences between the pca20006 and my board:
There is a 32 Mhz...
Hi,
it seems there was lately a new IC revision release of the nRF52840.
Is the nRF52840 IC Revision Engineering B 100% pin compatible to Engineering A, i.e. pinning...
Please excuse my basic question but I'm new to this - I am needing to have data collected from probe/sensor, which would be in a device, sent every hour to an android app...
Hello,
We plan to switch between two sets of UART pins for factory testing. One set will talk to an IC in our design and the other to a USB port through FTDI. Since simultaneous...
Hello,
We'd like to connect 50 bluetooth 5 devices (nRF52840) to a Receiver (made of multiple centrals nRF52840) with a long range (PHY 250kbps, conn interval 50ms, no...
We are evaluating the nRF5 SDK 13.0 to upgrade our projects from v12.0 and it looks like it has a bug related to the FDS functionality.
I managed to reproduce it on the...
Hi friends,
I am doing a project in NRF24le1 using RF communication with multiple nodes with a host using star topology.
Could you suggest a Protocol that supports connecting...
Hi,
to what impedance shall the BT antenna be matched?
Copying from the datasheet:
A matching network is needed between the RF pin ANT and the antenna, to match the...
Requests for the FW:
Add characteristic to access general GPIO pins in analog and digital form.
extension of the existing MOS_1-4 access, PIN read/write under the...
Hi,
We use nrf51 SDK v9. I found there are two SER_MAX_CONNECTIONS defined both in app_ble_gap_sec_keys.h and ser_config.h. Their values are different. One is referred...
Hello,
I have a problem when I try to use cheaper Android phones to communicate with our 52832 chip.
I can discover the peripheral and then connect, but when I device...
