I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Version: windows 11, vscode: 1.92.2 nRF connect for VS Code sdk: 2.7.0
Hello,
I am currently using the vsCode extension nRF connect for VS Code. This works fine, if i...
Hello,
I am currently using an NRF52840 microcontroller (powered at 3.3V) to control two IR LEDs (powered at 5V) via an N-MOSFET. The GPIO pin that controls the N-MOSFET...
Hi,
I prepare my custom board on nrf5340, and i have to use 3xUART, 1xI2C, 1XSPI.
Regarding product specification, i see i cannot configure more than 4 (UART,SPI,I2C)...
Now,I have a project writed by nRFSDK17.And I want to rewrite it by NCS.
I hope to get a module like peer_manager to manage paring and bonding,and I can distinguish connecting...
The status of Docker support is not clear to me. Does Nordic provide a docker images than can be used on Apple Silicon and Integrated with Visual Code Studio. I see a lot...
Hello developers, I am using nRF5340dk as my nodes and my gateway also. (3 boards).
Requirement:
i want to send my data from the board(1) to gateway with the help of mesh...
Hello,
I'm trying to configure the internal temperature sensor but have no idea ...
My board selection is raytac_mdbt53_db_40_nrf5340_cpuapp and, on nRF Kconfig GUI, I...
Hello, I am working on developing a special "serial recovery" mode dfu function of nrf52833 with ncs SDK V2.3.0. Now I encount a problem when adding the following code in...
I am attempting to get the BMI270 sample working on an nRF5340DK, using nRF Connect SDK v2.4.2, after successfully build and flash the program to nRF5340DK I got error "Device...
Hi all,
I am developing an application for a custom board using the nRF52840. I need to use the reset pin (P0.18) as a regular GPIO, configured as an input with an associated...
nRF5_SDK_15.0.0_a53641a s140 nRF52840
Documentation says that both ble_adv_fast_timeout and the ble_adv_slow_timeout are in units of 10ms, and that appears to be true of...
I have read some of the Asset Tracker documentation and noticed there is a nice implementation for operating LEDs in the UI module. This seems straightforward for GPIO control...
Hi,
We're having a problem that our application will hang when using the 32 kHz RC oscillator in the mcuboot bootloader and the Zephyr application. We encountered this...
hit there,
i am trying to work with the NRF5 SDK ARMGCC, in the IDE options a ARMGCC folder exists with an .ld file and makefile. i run the make and get the following error...
Hi,
I'm aiming to develop a custom two-wire serial interface (TX, RX). To achieve this, I'm planning to implement output capture for TX and use GPIO interrupts for RX. For...
