Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I can connect same sensor using nRF connect app. See attached snap shot.
The BLE connected Pressure sensor is advertising the Unknown Service using UUID : -- 18FF (First...
Ladies and Gentlemen,
I was wondering about the maximum clamping current of the Body Diodes of the nRF9160's IOs. There is no value stated in the product specification....
This might be a naive question, as I am a novice in this field.
I am making something similar to ble_app_hids_keyboard in sdk11, it will be configured as a consumer device...
I am using windows 10 and I was trying to operate my pca10028 board for a blue tooth connection. I pressed the reset button a few times but now its not working and only LED...
Can a corrupted InfoPage of the nrf24le1 be fixed from an ELNEC/Dataman programmer? I have read on the forum that th InfoPage can be restored from Nordic kits/IDEs, but I...
I am using an nrf52832 DK with Zephyr and I have a component that require a block of code to run uninterrupted. Specifically I am using HX711 with four load cells, and the...
Hi,
I want to display a picture with a screen (80x160) with st7735 and sdk 15.3 (segger embedded.)
I have some problems.
I use the function nrf_gfx_bmp565_draw, so I...
I am using the NRF9160 for SPI using an external Flash. After using the 'http_application_update' samples, I was able to get the value of the data written on the external...
Hi, I am a MCU developer searching BLE MCU to develop some IoT project.
I would combine nRF series and LTE NBIoT module for IOT project.
And I need to integrate many different...
Hello all,
I am trying to use my nRF52832 DK for a wireless camera shutter for my phone. I have reviewed the example code from SDK 15.3.0 named ble_app_hids_keyboard as...
Using SES, nrf52840DK, the onboard debugger.
I am able to set a breakpoint and use condition like x == 5.
I am unable to use anything but the == operator. In SES I...
On line 904 of nrf_log_frontend.c there is a log message to indicate the backends are flushed – but this message adds a log to the queue. If auto flush is enabled, this can...
Hi forum,
I am worked on nrf52832 using sdk 15.0.0.
How to used RTS and cts for enable HWFC on nrf52832.
Is their any example for HWFC control through RTS and CTS line...
