Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi,
Recently we have bought nRF9160 DK PCA10090 devices and tried to add to nrf cloud account but we end up with issues.
Following the standard procedure mentioned in...
Hello,
I noticed that when my Thingy is charging the Temperature measured is 4°C higher
The data are coming from NRF Cloud.
We can clearly see the temperature rising...
I use SDK16.0.0 and SD7.0.1-S132 Implement NUS functions, 1 * ble_central and 6 * ble_peripheral. The uart of ble_central connect to STM32MCU. My system run as follows, 6...
Hi. I tried to add rel_humidity_measurement cluster to multisensor example. New cluster is visible , but i cant get humidity data report I used cli exemple, here are logs...
Hello,
We have studied the getting started guide for the OTA upgrade at the link below.
https://devzone.nordicsemi.com/nordic/short-range-guides/b/software-development...
Hi all,
I was trying to evaluate the nRF52840 current consumption through the online power profiler. I set the tool as in the below image
there are three standby currents...
Hello guys,
I am attempting to send AT commands to an nrf9160 over UART. I started by loading the serial_lte_modem sample and sending commands using the LTE link monitor...
If I add
CONFIG_BT=y
CONFIG_BT_PERIPHERAL=y
to tests/crypto/prj.conf then CONFIG_ENTROPY_CC310=y gets turned off when building. By default, this will then cause a hard...
Hi
I am using the nrf52832 with the heart rate (freertos) example
Let say i want to add a new service and characteristic to that service ,this service is not suppose to...
Hi,
I have developed a simple system based around a Raspberry Pi Zero. The system uses a couple of sensors to measure temperature and water pressure using a ADS51115 A/D...
Hello,
I use NRF Connect Desktop on Windows 10 - 64 bits.
When I lauch the Programmer application with my NRF52 I have this issue :
2020-07-20T11:27:17.148Z ERROR Error...
Hi,
I am using the nRF5_SDK_13.1.0_7ca7556.
When I call the pm_conn_secure(), it returns NRF_ERROR_INTERNAL.
Can you tell me why did the NRF_ERROR_INTERNAL occur?
...
Hi ,
I followed the getting started steps and enabled the global sim. Now the LED 3 is blinking .
In the LTE Link Monitor , I see the following :
2020-07-22T03...
When I enable watchdog in main application by:
nrf_drv_wdt_config_t config = NRF_DRV_WDT_DEAFULT_CONFIG; err_code = nrf_drv_wdt_init(&config, wdt_event_handler); APP_ERROR_CHECK...
I'am currently porting an existing application that makes extensive use of the app_scheduler to FreeRTOS. To speed up the migration I have enabled the app_scheduler in the...
