Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi.
I need PC app communicate with my development board though BLE.
so I'm testing pca10059 with ble-pc-driver sdk.
I tested ble_app_att_mtu_throughput example with...
Hey, I am trying to sample from 10 analog sensors and stream the results via bluetooth. Since the nRF5 is on a board that only lets me access 5 Pins, I am using a 16:1 multiplexer...
Hi everyone!
At the begining I want to write what I'm using to make everything easier.
Device:
- NRF51822 xxAC ( This one ). - GSM module Simcom Sim 7000E ( This one...
I need to be able to upload my application to an nRF52832 through an ARM architecture Linux machine that I have remote access to. nrfjprog is not available for machines with...
Hello. I connected the Image transfer service (running on a nrf52840) to another nrf52840 running a modified BLE_NUS_C service.
However, a BLE packet won't be send out,...
Hello,
I have the following issue when trying to detect which GPIO triggered the interrupt:
For my low power application, I was trying to connect two switches to the...
Hi,
I'm in the process of designing my first prototype with the nRF9160 SiP. For the LTE antenna sub-circuit, I simply want to replicate (as much as possible) Nordic's reference...
Hello,
I am using custom nrf52832 PCB as central role. Also i have the peripheral with similar board . Peripheral communication is working properly if connected with the...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Similar to WiFi and 802.15.4 where there are...
Hello,
Customer want to use
nRF51822 Bluetooth Smart Beacon Kit
with this requirements:
We need the most simple beacon. Additional sensors are not needed. Its main...
Hello Nordic team,
I'm using nrf52840 DK with SDK 15.3.0.
So I had an example sending data similarely to the ble_app_uart_c example that worked OK.
Basically I have...
Hello there!
We have a running prototype with an NRF24L01+ and ESB. But since it is not recommended for new designs, is there a successor for this setup?
Very low latency...
Hello everyone,
I have trying to store my serial data in nrf52832 SDK15.2 fs flash storage i need to appending data one by one in same file. i have using fds_record_update...
Hi,
I use nrf 52832 with pca10056 and i need to use float to filter my data with low pass filter, but with this device, it doesn't work. Do you know how can I use float...
I merged ble_app_uart with spi peripheral example, normal working like bluetooth connectivity, spi sending and receiving is working fine, but i want to transmit data received...
