Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi,
I need to check the emission of my custom nrf52832 board design and I need an spectrum analyzer... To see if my design would pass the regulations and tests.
I was...
Hi Nordic,
It's hard to find an example to talk about the event of advertising. I checked the advertising chart and know I will get the event BLE_GAP_EVT_TIMEOUT. Where can...
Hi,
I attended a training session run by the BT SIG last week and met a helpful Nordic chap who, when I mused about how I was using a programming board to run a sensor...
Hi i am having doubt in RTC configuration.I am using RTC1 and i want to produce ticks for every 1 minute.I have combined the UART and RTC example to get the RTC output in...
Hello
i am using the Nrf52 with pca 10036 board. i am working on fruitymesh to work on visualgdb.
i am getting problem here
"#pragma pack(push)
"#pragma pack(4)
...
Hello, i need to count 1 or 2 minutes. Someone can recommend me if to do that is easier to use app_timer or RTC?
Which is the value that i have to put in the prescaler...
Hi,
I have bootloader ,Application with buttonless dfu (with FreeRTOS) and S132 v3.0,
Flashed SD3.0 and then bootloader with debug support. After updating application zip...
Hi all
I use the nRF52832 and the SoftDevice S132 V2.0.1. When I perform a soft reset (NVIC_SystemReset) while the SoftDevice is running, the fault handler is triggered...
Sorry i'm survey in forum ,and try for a week , the problem still there , please help me !!
I'm try to compile APP1 in IROM1( Start:0x1B000 Size:0x4650) ,APP2 in IROM2...
In Nordic's example GCC projects, the Makefile of the SD examples have -DSOFTDEVICE_PRESENT defined. However I noted that even though it is defined here, in nrf_drv_common...
I have a 1 second app_timer running which increments a 1 second variable used as unix time. We have a 32Khz Xtal, etc, which should result in good accuracy.
I have noticed...
The QFN package has an exposed gnd pad. Are thermal vias required in this gnd pad? The reference design has a 4x4 thermal via array. I believe this is only there because Altium...
Hello,
I'm using a BMD200 module (with a nRF51 chip inside) and the custom_board.h provided by Rigado along with their EVK. I'm also using a BMD200 on a board I developed...
Hi There,
Under what condition(s) would a master skip a Connection Event (i.e. not transmit to the slave)?
We are currently testing using v12.1 SDK. I have configured...
After connect I try to find a service using MasterEmulator method DiscoverPipes() . I'm using event masterEmulator.LogMessage += OnLogMessage; to print logs. First it write...
