i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi! I'm testing the application with the custom Battery pofile I generated with nPM PowerUP app. During testing I found the issue with the SOC value calcultation depending...
Hi Nordic Team,
I am planning to develop a SmokeCo device using the nRF54L15. I tested the example code of Smoke-Co from nrf-sdk with nRF54L15-DK and that working correctly...
Is there a trick to getting nrf_dm to compile on the nrf54l15?
I've installed v2.9.1
Command I normally use (nrf52840):
west build -b nrf52840dk_nrf52840 -d build_nrf52840dk_nrf52840...
Hello,
I am using the following device and development kit:
Device: NORA-B106-00B (nRF5340)
nRF Connect SDK: 2.0.2
Currently, I am trying to use GPIOTE PORT...
I've been trying to run the example Mesh/Chat on NRF7002DK, and the terminal print <err> bt_mesh_pb_adv: Failed enabling advertiser and <err> bt_mesh_pb_gatt: Failed enabling...
After using the backup v2.9.0 project to overwrite the original project, I encountered the following issues during compilation： How to solve it? Using Windows not Linux. Thank...
Hi Devzone
We found that the NRF54L dk will stuck if add systemView function into the bluetooth sample project
we add below config into peripheral_uart/peripheral_lbs...
i brought Power profiler kit II deveice and try to measure current on it.
i couldnt get proper measurement can you please help me on this? it is giving some random value...
Hi!
I have an NRF9151LACA AEA device and I'm trying to get it to work. Got the IMEI and the device successfully connects to cellular network.
However, I can't get HTTPS...
I am developing an app for a custom nRF52840 board. I am using the latest version of the nRF Connect SDK (2.9.1) and have enabled OTA DFU in firmware using MCUboot and sysbuild...
Dear Nordic Support Team,
I am working with the nRF52840 in a multi-protocol setup and would like to clarify the feasibility of the following configuration:
Running Thread...
Hey,
we're currently testing our devices with Modem FW 1.3.4 / nRF Connect SDK 2.2.0 and have observed the following error:
LTE-M
Connection was successful before...
Hello Team,
I am using nrf54l15 dk for the development. In this, I am using k_sleep to put the device in system-on sleep mode. Using this, I have achieved the sleep current...
Hi,
I need to use AES CBC 256 encryption/decryption on nrf52840 but since its cyrpto cell only supports AES 128, I tried using mbedtls to do AES 256 encryption. It works...
