Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Dear Nordic,
As per power management, could you please suggest any thoughts for following:
We have two ICs on the board connected to nRF52840: 6-DOF sensor (over SPI)...
I took the RSA example in /nrf/samples/crypto/rsa and added a function foo() to it. I am using nrf5340DK with nrfConnect v1.6.1 and build for cpuapp.
my function foo() uses...
I now burn the official routine through the serial port input instructions, want to make NRF52840 dongle read zigBee terminal equipment (temperature and humidity sensor) value...
There is a task to run a sniffer without Wireshark on windows. I'm using your example that comes with the SnifferAPI nrf_sniffer_for_bluetooth_le_4.0.0. After successfully...
After the command "zdo mgmt_lqi 0x0000" is successfully used to obtain the short address of the terminal device, you cannot obtain the short address of the terminal device...
Current I am using nRF52840 Dongle to develop a Bluetooth PC Tool base on nrf_ble_driver_obj_sd_api_v5 which shared on https://github.com/NordicSemiconductor/pc-ble-driver...
Hi Nordic Dev Team,
I need suggestion on how to achieve this. My microSD saves chunks of 50kB raw data.
I would like to retrieve this data once connected to the phone...
Hello,
I am trying to receive advertised data by a sensor which is easily detected at nrf connect app and whenever data changes i am able to see the change in data on nrf...
I am trying to send a lot of data and I am trying to do this with notification. As I understood notification do not need acknowledgment and should not use que for messages...
Hello,
I am using SEGGER embedded studio to develope a project. I want to know how can I know the flash and SRAM use of part code. Because I have many files. After I build...
I am using the nrf9160 for an OTA firmware update application. After going through a lot of tickets and some documentation regarding the nrf, I have not been able to find...
I want to use the register of Nordic's P0 port directly to set 1 or clear 0. Like this,
p_reg-> OUTCLR = clr_mask;
P_reg - & gt; OUTSET = set_mask;
p_reg-> OUTCLR...
Currently we are developing against hardware sensors etc. that we have installed in our warehouse
It would be great to be able to develop remotely (ie. from home) without...
Hello Nordic Support Team,
I'm using nrf52840 DK for DFU update over ble with nrf5 sdk previously it was working fine and i was using nrfutil tool to generate settings,...
