I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi Nordic,
I was checking the ble_app_uart_coexist example application and it says it is a combination of both UART & Mesh. So would this support provisioning via mobile...
Hi, team. ********** environment : SDK : Mesh v3.2 (w/ SDK v15.3.0) SoC : nRF52840 IDE : SES ********** I am challenging to handle each event, such as Mesh receive interrupt...
Hi all,
Radio notification inactive state interrupt is coming but I was not able to do any action by comparing it.
I am thinking, if radio_evt is false then it is radio...
Hi,
I need trigger repeated SPIM via PPI for a batch of samples until the given RAM buffer is full. Then I need start another round of batch SPIM with another buffer.
...
Hi,
I am trying nrf52832 with pca10040 board. My app uses s112 soft device and also SPIM0 to collect data from a slave device. No event handler has been used when initializing...
I want to know how to control BLE connection of nRF52832. I am using softdevice S132. I have a device that works centrally and a device that runs peripherals. When the peripheral...
nrf52832.
SDK14.2
Segger ES V3.34a
Options for Sequential Serial numbers
We have managed to program a single serial number into the UICR, using our Development...
I am trying to interface I2C EEPROM (AT24C512) with nrf52840 and I am directly writing to and reading from the registers mentioned in the datasheet. I am seeing the i2c waveforms...
Hello -
We are also bumping into the problem described here , where it is not possible to initialize LESC when BLE is initialized from a FreeRTOS task. The nrf_stack_info_overflowed...
nRF52DK
external board with 51822 and mems
I connect my external board with nRF52DK as this (left is board, right is nRF52DK):
SWCLK -> SWDCLK
SWDIO -> SWDIO
VCC...
Hi,
I got some troubles on the communication distance between the two units which one acts as central and one acts as peripheral, I tried to adjust the BLE parameters the...
Dear Sir,
I have enabled my project for SPIM+EasyDMA.
I am configuring the SPIM transfer nrf_drv_spi_xfer with additional flags like,
NRF_DRV_SPI_FLAG_NO_XFER_EVT_HANDLER...
nRF51822 QFAA
At first I set up the RAM size to 0x1F80, it works fine. However, after I try to use RTT to print log, I got the compile error: region RAM overflowed with...
