Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Would a wire-wound inductor work better than a chip inductor for the antenna circuit of NRF52810? I'm using the 32 pin QFN package with the LDO configuration which calls for...
I need to calculate the max number of concurrent connection Central can support given the following
Connection Internval = 7.5ms
Baud Rate per connected peripheral:...
Where can I find this version of hub?
ERROR: Could not find a version that satisfies the requirement hub==2.0 (from -r zephyr/scripts/requirements.txt (line 10)) (from versions...
When nrfutil is installed with python 3, I get an error when generating bootloader settings page. This does not occur with python 2. As python 2 support expires very soon...
Hi.
I am testing MESH by nrf5SDKforMeshv201src and nRF5_SDK_15.0.0_a53641a.
I have a problem.
My project have one of the client and one of the server.
Client transmit...
Hi I had a question to setup the MCP2515 driver in the zephyr project.
We have a custom board for the decawave DWM1001 module, which uses a nRF52832 chip. They have a device...
Hello I am using a I2C sensor module and I need to tranmit only address to receive data back, but I dont know how.
Program crashes on line 4.
Thank you for your help...
I have a DK52 with another device at attached to the SPI bus. I also have a PPK. Should
I connect the second device to VDD_nrf to count as a load? right now it is connected...
When the bluetooth service function is initialized, sd_ble_uuid_vs_add() is called in the ble_dfu_buttonless_init() function in case of an out of memory error. In the ble_nus_init...
Hello, Is there any evaluation kit available for NRF905? I found this one online but DIGIKEY website says its obsolete::
media.digikey.com/.../nRF905-EVKIT_PS_Rev1.0_Jan2004...
Dear Nordic staff and users,
Now I'm trying to confirm that my local LTE operator supports energy saving modes. It went with flying colours with PSM:
at+cereg=5 OK at...
using SEGGER Embedded Studio for ARM V4.30a, I get a problem of Linking with an nRF5_SDK "blinky" examples. See hereunder the error message:
Seem to be a problem of configuration...
Hello,
I can create a zip file with nrfutil pkg generate and there is a bin file in it? I want to make DFU as a bin file only.
I only want to download the firmware as...
Hello,
I have a question about using pins as output. I'm trying to set 2 pins to "1", but cant fully understand how to use pins on port1.
for example: P0.10 (wich works...
