hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,
I'm trying to use RTT Logging in my application. If I build and flash my application through Segger Embedded Studio RTT logging works. However If I use ARM GCC to build...
I'm not able to carry out monitor mode debugging. I'm referring https://github.com/NordicPlayground/j-link-monitoring-mode-debugging/blob/master/pca10040/s132/arm5_no_packs...
Hello.
I almost finish nrf52-quadcopter develop.
I want fly drone with mobile.
I want to confirm PID value from minum to maxium in mobile.
and I want to confirm your...
Hello Nordic team
I am working on nRF52840 DK, SDK-15.0.0 with ble_central example. I need to give support of DFU like we are doing with ble_peripheral example.
My question...
Hi, I have a question for you! Thank you!
My PCA10040 was not successfully connected to the computer.
The device manager of the computer did not show anything related...
Hi
i am using SDK15.0 .i have tested Secure Ble for firmware update. Its working with my public keys. i want to know is it possible to update firmware without Public key...
Hello,
I am trying to find the IP address of the devices.
Device: nRF52840 DK
Setup: Running virtual Ubuntu 18.04 inside Windows 10 (using VMWare).
I am able to connect...
Is there any recommended way to flash the nRF51822-CEAA-R WLCSP chip?
Should a PCB design have UART design for flashing the nRF51822 chip after it is soldered on? Or should...
Hi, My problem is: When I programing my board using existing hex from SDK, I have no problem. Program working great. But if I building my own hex (build without errors) and...
Hello,
I am using nRF52832. My GPS is connected to GPIO pin (15, RX) and (16, TX) of nRF52832. My TCA9535 is connected to GPIO pin (8, SDA) and (7, SCL) of nRF52832. TCA9535...
Hi all,
I am currently building I2C communication between nrf52832 and a stm32 chip, stm32 as the master and nrf52 as the slave.
The situation is the stm32 couldn't get...
I am not connecting any uart lines to the device. But I feel the assert is being used as the timeout "handler" and then pressing button one resets the device.
I'm using...
Hi,
I'm currently going through this paper on the newest Bluetooth Mesh Standard ( http://www.mdpi.com/1424-8220/18/8/2409) . Although it's interesting to see that this...
Hi, we are using SoC nrf52810 SDKv14.2-SR3v1.2 for our RCU.
1.If there is a scenario the image transfer is finished, and the power lost happens when the old image is being...
