This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Since Nordic offers BLE sniffer tools including its hex code, I would like to flash it to my own USB dongle as a test. I insepected the hex code, and found its address starts...
Hi All,
I am new to the nRF processors (but not new to embedded progarming). Trying to use the evaluation board with the examples on the SDK. After realizing the freeware...
Q0. What IRQ Priority does BLE Has? and also what IRQ Priority does UART can have?
I'm guessing that from s130's document P65, Exception Model, It says,
Softdevice Timing...
Hello,
I could not set breakpoint in Eclipse. I set CFLAGS to -O0 and -g3 in Makefile
I am using GNU Tools ARM Embedded 6 2017-q1-update and Eclipse Neon3
Below are...
Hi,
is at the moment possible with S110 (nRF51 SDK) to whitelist only SOME of bonded peers? I need to allow connection from one selected central. Selection is made by user...
As a follow up from devzone.nordicsemi.com/.../ , I am now trying to find out if I am getting all of the memory settings put together correctly. When I have them at higher...
I am using nrf51822, 16K RAM, 256K Flash.
From the movie , there is no way to secure my firmware for DFU. Is there any other way to secure my firmware?
Thank you
I know the many differences coming in bt5. Will the programming concepts be the same in the upcoming 5 version? IF my code is working with ble4.1 will it automatically work...
After a bunch of headache I was able to successfully program with the nRF51822 Development Kit without the nRFgo Starter Kit motherboard, here is how I did it.
Hardware...
I'm working on a design that incorporates an nRF52832 along with some sensors and drivers.
Up to this I've been sacrificing power consumption in prototypes by using LDOs...
Hello,
Is it possible to change SPI baud rate whenever we want?
For example:
The initial SPI baud rate is set to 4M. We want to change the baud rate to "2M" to get...
Hi,
This may be stupid, but I can't declare classes in my .h file in keil. I have arduino library for my I2C device, but keil; does not recognize when I declare classes...
I've looked through and tried many examples on getting my SAADC to produce a temperature offset. About a month ago I had the SAADC working really well with a wheatstone bridge...
Hello,
What changes need to be made to the following tutorial to enable basic advertising with the Rigado BMD-300 on a custom board breakout board?
devzone.nordicsemi...
Hi,
I have multiple devices set up in a simultaneous peripheral and central mode that exchange data on connection. As there may be multiple devices around, I want to make...
