hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello
Is there a possibility to build MCUBoot, SoftDevice, Firmware Loader and Application separately and then merge it manually? Or to build MCUboot + SoftDevice + Firmware...
Hello there,
I am working on a project which involves nRF52840 to scan and connect to specific BLE beacon.
So while scanning, nRF writes scanned data on UART. On same...
Hello,
I'm running SDK v.2.8.0 and developing using the nRF5340 Audio DK. I've successfully flashed using the buildprog.py script, and have set up my DK as an Auracast source...
Hi
1. At nRF5340 datasheet page 420, the PDM duty cycle is 40%~60%, any register can tune duty cycle? Or it's nRF5340 variation tolerance?
2. Since our DMIC IM69D128S...
Hi all,
I'm testing Skylo NTN on nRF9151 SMA DK with the latest pre-commercial/alpha NTN modem firmware (downloaded mid-December 2025).
Registration works fine, and uplink...
I am trying to get the nrf/sampoles/bluetooth/direct_test_mode working together with the code from zephyr/samples/subsys/usb/dfu-next.
I have the DTM mode running correctly...
Hello,
I think there is typo on page 541, in the PWM, Pulse Width Modulation, section of the nRF52840 Product Specification V1.11.
It states "pulse with modulation", but...
Hello,
I have a question concerning the neighbor cell measurement feature on my nRF9160.
After some tests, it seems to be sensitive to the operation mode. For example...
I am currently working with nRF52810 using nRF Connect SDK v3.2.1 , and I am trying to run the AES CCM PSA Crypto sample .
However, when running the unmodified sample, it...
hello i am new to the nrf trilateration and direction tracking using nrf52840, i need some help with the sdk and programming and working examples .
eg : I have 4 nrf52840...
Unable to connect JLink via USB. Installed different versions of JLink without success. Device Manager showns "J-Link driver" under Universal Serial Bus controllers and nrfutil...
I'm using a custom development board and I want to enable timer 0 through the external 32MHZ crystal oscillator. Here is my configuration:
prj.config: # Enable the UART...
I am trying to live capture and analyze traffic on Wireshark. I followed lessons like https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson...
Dear All:
I have a very strange issue that has me scratching my head. I am programming a GPIO to provide hardware reset to an i2c GPIO expanver (pcal6408a). The io expander...
