hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi Nordic DevTeam,
What I have learned from this thread below is that using 32kHz external crystal provides less power consumption and better accuracy :
https://devzone...
To the kind Nordic support team,
We are evaluating a scenario where we need a "gzll gzp host" to receive data on two encrypted pipes at almost the same time (we modified...
i was running some power optimization and MTU tests in NCS V1.5.1 and was able to compile and run.
I upgraded to NCS V1.6.0 and there were several errors
So when I compile...
Hello,
I am currently working with the development board nRF5340DK in order to evaluate the nRF5340 SoC.
Given certain project requirements related to the operating temperature...
Hello,
I am new on Nordic controller platform and i want to make the GPIO pull down and pull up at run time and also change the IO direction.
How i can do that please...
I am using the FAT FS on the nRF9160-DK to store data on an SD card.
The CLIB library provides Linix-like fopen, fclose, …
The flags passed to fopen are strings like ...
hello,
i am using nrf52832 with sdk 15.2 using ble_app_uart example and my beacon stops axdvertsing after sometime can someone help me how can make it advertise continosuly...
I am currently evaluating nrf52840 - CDSENET E73-2G4M08S1C module with installed CircuitPython 7.0.0-alpha.3. Unfortunately the ADC readings are quite noisy. For example for...
Hi, i'm using hte Keil and a custom board with NRF51822. The question is where i can read the value of a custom service? I make the configurations like this tutorial ( http...
Hi,
I have an application where it would be beneficial to be able to send get and set messages to individual groups, nodes elements, etc. All of which are not necessarily...
why doesn't the mesh chat example work on nrf5340?
I know it's not included in the list of supported platforms, but I'm trying to figure out why.
I can compile and upload...
Hi,
I've noticed that when I'm not initialize BLE stack, I have a failure in nrf_sdh_soc_evts_poll function (NRF_ERROR_NOT_FOUND).
Can you please explain what is the reason...
Hello:
nrf_pwr_mngt_run() doesn't always work on my custom board. About 1 time in 3, in code (I'm running in debug mode and using RTT) spits out
ERROR 3735928559 [Unknown...
