I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Versions:
Windows 10 Enterprise: Version 1803
SEGGER Embedded Studio for ARM (Nordic Edition) V4.20a (64-bit)
Python: 3.7.4
pip: 19.2.3
west: v0.6.2
nrf repo:...
The nRF5SDK has a rich set of examples illustrating extensive use of the BLE APIs, including full examples of the Blood Pressure profile and other health device profiles....
Hi,
I am using nrf51422 dk board using sdk 12.3 and soft device s130 in keil5 ide. In our project i am using nrf51422 board as central and other controller Bluetooth board...
Hello,
I'd like to evaluate the Rust HAL for the nrf52 family of devices. But before that I was asked to inquire about the stage of development of the HAL and the support...
I am experiencing an issue with the nRF52840 dongle and programming UART pins. First off, I have developed my application on the nRF52 DK and it works fine and now I am programming...
Hi , I need use the DFU ble without have to generate a packet with the nRFutil. I wan't put a open bootloader on the board, don't need to be secure just easy and fast. But...
I am trying to find the hardware datasheet for the speaker on the Nordic Thingy 52 - can someone help point me towards it?
My end goal is to learn about the characteristics...
Hello!
I have been trying to implement the serialization for STM32L476. During my development I discovered that the deserialization of the SD_BLE_GAP_ADV_SET_CONFIGURE response...
We have a custom board with nrf51822 chipset, and we need to implement the firmware update process, which can support both over-the-air and uart type firmware update.
1...
Hi, we are contemplating moving an existing application to a nordic chip, the nRF52832.
https://infocenter.nordicsemi.com/pdf/nRF52832_PS_v1.4.pdf
Our previous CPU uses...
I'm in the process of implementing a custom layer above ESB in order to allow more than 8 devices to communicate with a receiver (By tagging packets with a device ID)
I...
I used nRF52 SDK V15 and tried to load the sample BLE HID apps into the nRF52-DK Development Board.
I tested both ble_app_hids_keyboard and ble_app_hids_mouse. Both apps...
We have exiting BLE 4.0 device, which should be updated to the mesh. nRF52832
In the DFU for BLE4.0 you could update the booltoader and the softdevice with one update, with...
