Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using the nrf52840 DK. Have the debug section of the board turned off. I have the external flash removed from the circuit. I am using a 3V external supply. I am using...
Hi,
In any of the documentations, I could not find the Antenna Gain of the nRF52840 development kit. Could you please point out to me where I can find Antenna Gain or any...
Hi,
On NRF9160DK, there is a nrf52840 chip.
I want to use nrf52840 as a host controller with NRF9160, but I cannot find any example to control nrf9160 by nrf52840. ...
Dear support team & community
Our company tries to integrate communications between our NRF52840 -based product and a Philips Hue Bridge gateway. We successfully connect...
hi ...
how to merge the serial uarte and ble_app_uart .... i want to getting the data through the serial uart and i need to transfer the same data over ble .. please guide...
Hi,
I have implemented a hx711 sensor readout with PPI, using SPIM and PWM peripherals. But for this is needed 4 GPIO and one external OR Gate. I wait for a LOW pulse on...
I came across the nrf-connect SDK sample UART : https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/uart/src/main.c . I was wondering whether...
Hi team
I want to config interval via LL_CONNECTION_PARAM_REQ.
But nrf5 looks like use L2CAP CONNECTION PARAMETER UPDATE REQUEST to send request to change config.
But...
Is there any reason the pin reset hold time is not mentioned in the nRF52832 product sheet? I've seen in the forums that it is same as nRF51, which is 0.2 uSec but I would...
Hi
We are using BL600-SA in our project. I need to configure NRF51822 transmit power so that it is discoverable at particular distance.
I am using softdevice S110 and...
Hi.
I am newbie and trying some sample examples from nRF52832 SDK for mesh to gain knowledge of Bluetooth mesh
I have nrf52832 Development Kit and I am trying examples...
Hi! We're developing a BLE-sensor for tracking small animals. In the past we've used a different brand of BLE-module but we're looking to switch to the nRF52840. As we're...
I want to use my "nrf51 DK" module as a BLE sniffer for which guide is provided at https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf but I also need " nRF Sniffer...
