Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
I did current measurement for NRF52840. For mesh light switch demo example measurement was 10 mA, and for Thread CoAP Examples current measurement was 0,6 mA. I don't understand...
Hi all,
I am developing an application for a product where power consumption is critical. The application is bundled with the Secure DFU bootloader. I noticed that the bootloader...
Hello,
I think the question may be more related on how Wireshark works but I plan to do the following:
* use the v2 sniffer firmware and the Nordic Wireshark plugin
...
When I migrated, the reference routine output PWM, but kept reporting errors. I have also changed the relevant definition, but I still can't. Has anyone met it? Thank you...
Hello,
We're evaluating the Laird BL654 using your nRF52840 (to be precise, we're using two DVK-BL654-1.0 development kits).We tried to use the 'blinky' examples (ble_app_blinky_c...
Hi everyone,
I am developing a remote controller using nRF52832 chip. My prototype is currently developed in PC10040 board. The IDE is Eclipse Oxygen, and the SDK is S132...
Hello, everyone~
I plan to use the Low Energy Secure Connection funtion with nRF51822. But when I build the lesc example in SDK 12.3.0 (ble_multirole_lesc), there's a error...
Using the sdk15 and softdevice 132 v6, I'm setting up an app to read and write to an SD card that uses SPI1 (SPI0 is used by a display). Everything is working great, except...
Hi,
What's is the max length for the payload data in "mqttsn_packet_sender_publish" method?
EDIT:
Redefining my question above: What's is the max length for the payload...
Hi Sir,
According the table 19.4.2 of 52832 datasheet (v1.4), there is a start up time (0.36 ms) for HXFO.
How do I measure the start up time of my 32M crystal?
If...
Hello,
While an attempt to develop solid security mode bulded around Root of Trust starting from RTL and Device root key we found that unfortunately, it is mentioned in...
I would like to detect if a reset happened due to a brownout or an actual power off.
I tired so far using the GPREGRET and RESETREAS registers. They are useful to detect...
I have an app that works perfectly when run from the debugger, but not when started by HW reset. We use the serial port to communicate to a control processor (STM32) The Nordic...
Hi,
I was trying to test a slot circle antenna with nRF52832 which is well matched to 2.4G~2.48GHz, but it is circular polarized antenna with high directivity.
However...
Hi All!
I use nrf51822 with sd s110 to send data to android phone with sd_ble_gatts_hvx. If sd_ble_gatts_hvx returns NRF_SUCCESS then that packet get to TX buffer. I didn...
