I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
hi,
i am using NRF52832 DK, and sdk 15.0.0.0 ,,
i want make the central to work also as a peripheral...i.e whenever central is not working ,or ,central is not in connection...
I am evaluating the throughput of BLE communication between 2 NRF52832's, 1 acting as a central and 1 as a peripheral. I've modified the ATT_MTU Throughput Example, and I...
Gone through sdk 11.0.0 Experimental_ble_blinky application, i trying to assign one gpio pin in place of connected LED. what is it receiving when pressing on & off switch...
Hi,
I'm working with nRF52832 chip following the example "ble_app_beacon". I see the advertising packet is limited to 31 bytes only. However, I'd like to take an advantage...
Hi,
I have arm based application processor and need to connect with nRF52840 using UART, I don't have any idea about bootloader and factory firmware when hardware assemble...
We are trying to determine the emission designator for the nRF52832, or at least to determine the necessary bandwidth so that we can create the emissions designator. Please...
Hi everyone,
I have a problem with SOME android devices.
In particular Android devices with BLE 4.0 & 4.1, but I have NO problem with Android device with BLE 4.2 and iOS...
Hello,
We are using nRF52832 DK with SES IDE and latest SDK 15.0 sd 132. We have developed one multiplink central device and modified ble_nus_c with our application to connect...
I use nRF52832,is 2.5v power supply,but you can't download the program,w hen I set the voltage above 2.8v, I can download the program,then I switched the voltage to 2.5v and...
Hi everyone
I am able to send the data over the UART to the Real Terminal and also to my other device working on UART protocol. However , I am not able to read the data...
Hi,
I am willing to migrate sdk 14.2 code to sdk 15.0 code. Do you mind me to ask a crypto micro-ecc question, please? Thanks.
In sdk 14.2, the micro-ecc part definition...
Hi,
I am working on nRF52832 board using Segger Embedded Studio for ARM 3.34a on windows 7 64 bit setup.
When I am trying to initialize a structure in Flash memory, the...
I'm developing TWI code for Bosch BNO080. They use SHTP protocol on top of TWI. A working version using Wire library of Arduino is posted here .
I ported the code, and...
Hi there,
I'm playing around with the stock hrs_relay example that I've modified. the code works well but I'm noticing that its advertising strength is crazy high.
I was...
