Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi I'm doing a school project where I'm going to make a bluetooth mesh network where I use nrf52840. where i tried to get "light_switch demo" to run, but i have some trouble...
Hello,
Could it be possible to do an update with a zip DFU file stored in a flash memory ?
What is the best way to do the modifications (mainlines) ?
Thank you
Hi,
I'm using two nRF52832 (SDK14.2, SD132v5) to send data via Notify to one central. This central can be either a laptop or a smartphone.
The two nRF52832 has the same...
Hi all,
I am using nRF52832 SoC and nRF5 SDK for Mesh v1.0.1. I know until now there is only support for relay feature in the Mesh SDK. I want to implement low power feature...
Hello,
I was trying to connect my boards to nRF Cloud to evaluate it. Setting up Gateway on the phone and on the web at nrfcloud.com was rather easy (just following getting...
I use the SDK9.0，When a bluetooth device and android APP to connect, disconnect the bluetooth device power, why wait for 20 seconds, the APP to detect device has been disconnected...
Hello Everyone,
I want to know that i purchased NRF51 DK ..which includes PCA10040 IC.i'm using MDK ARM KEIL5 . now if i'm going to develop one BLE product so i don't know...
Good morning.
I have two nrf-51 boards and a mobile device, the SDK that I´m using is the v.12.2.0. I need that the three devices are connected at the same time and its...
Hi all,
My configuration:
nrf52832
Softdevice S132 V4.0.2
Nordic SDK 13.0
I'm using th e secure bootloader example located at \examples\dfu\bootloader_secure_ble...
The nrfgprgret register is used from the application(custom) to trigger the system into dfu mode. The nrf 52 enters dfu mode and a zip file containing bootloder.bin/.dat and...
hello, I check the standard example nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs device nrf52DK PCA10040 V1.1.1 ARM Compiler :...
I am currently considering purchasing the UBLOX NINA-B1 module. This uses the Nordic nRF52832.
The very 1st thing I wish to do is to be able to send and receive information...
Hi Nordic,
I have managed to make a board which has both the nRF52 and PN532 modules on the same board (picture) , connecting it through I2C as shown on the example here...
The Event Generator Unit peripheral is new in nrf52. There is a basic description in the current manual of nrf52, but not much can be inferred as to how to use it. Could an...
