Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello support team,
I am developing a mobile app to communicate on BLE coded phy (long range) with nrf5340DK. The nrf connect for mobile on android works fine, but not ios...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
Hello,
I am going through the intermediate DevAcademy tutorials right now because I specifically need to use the 52840 dev kit to interface with a SPI driven ili9340 device...
Hi everyone,
Edit: Consider that I'm on ncs 2.6.1
What are the current methods for provisioning an nRF9160 on the nRF Cloud? I have an ongoing project with the nRF9160...
This sample can be found under samples/nrf_compress/mcuboot_update in the nRF Connect SDK folder structure.I want to know the whole decompression process,I added a lot of...
Hi,
I am building an app that connects to the NRF52840 with BLE. The NRF board is attached to an electrocardiogram(ECG) setup, so I am interested in the app being able to...
Hello,
I am using the hci_usb sample from Zephyr and running BlueZ 5.53 on Ubuntu 20.04. I am trying to increase the ACL packet size from the default value of 27 bytes and...
Hi,
I am using SDK v2.6.1.
Is there any course available on DevAcademy for WebSockets?
For WebSocket i take reference of v2.6.1/zephyr/samples/net/sockets/websocket_client...
Hello there,
I am using nrf connect sdk using vs code.
Toolchain: v2.7.0 SDK: v2.7.0
I have custom hardware board based on nrf52811 SoC.
I have completed a firmware...
Hi
We have a project previously built on NCS v2.6.0 and now we need to migrate it to v2.8.0
I see from v2.9.0 child/parent build setup is not supported and so we are planning...
I'm using ”ncs\v2.8.0\nrf\samples\nrf_compress\mcuboot_update“ this routine.After connecting the Bluetooth, put in the DFU package (mcuboot_update\build\dfu_application.zip...
Hi,
We are trying to enable oversampling in an application that is based on your DF connectionless RX sample, build with Zephyr version 3.4.99.
Something similar was asked...
Hi,
I've a good experience with nRF5340 pre-certified modules and nRF Connect SDK. I'm evaluating leveraging Nordic Thingy:91 X platform to build a new product. However...
Hi Team,
I have some questions following,
1. We created custom board by using nrf52833. for custom board any bootloader needed?
2. We are able to flash hex file into...
Hi i am currently, doing development on nrf52840. where I have 48 number of GPIO's available. for my application, I have peripherals like Touch screen RGB display, UART based...
