hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
hi nordic,
After i received this kit from Mouser Electronic, when i got it check the board which some question,
we examined its outward appearance and found that this...
Hi,
I have my nrf52 DK. I would like to advertise as Beacon and be BLE (which I can connect to via iOS app) device at the same time. Do you know any examples of this kind...
Why does the macro CHECK_RAM_START_ADDR only check for C_LINK_CNT and P_LINK_CNT and not the SEC_COUNT? It is always set to 0 in the macro.
I have increased the central_sec_count...
Hi ，
I use timer to handle pwm signal,
1.when calling button by phone is pressed,
Timer starts,(function:on_key_trig_speaker_event())
2.pwm signal run (speaker_meas_timeout_handler...
Hello,
My name is krishna,
I have couple of NRF24L01+ modules,
I am trying to implement MultiCeiver in the NRF module.
The problem is i am able to receive or transmit...
Hi,
I am trying to compile the ANT Broadcast Tx Example from the latest nRF5 SDK v12.1.0 (../examples/ant/ant_broadcast/tx), but I get the following 3 error messages with...
Hi,all
I use nrf51822 connect with ios device,it will automatically disconnect when links more than 90 seconds.
device connection parameter as follow:
#define MIN_CONN_INTERVAL...
Hi I'm using the Jlink to program nRF52832_XXAA, by using nRF command V9.0.0 nrfjprog
I success in erase , but I can't program correctly,I tried Jlink version 5.12g and 6...
initially we developed code for arduino mega board but now we want to use the nRF51822 soc,so how i can utilize my arduino code for nRF51822 ....i have gone through the some...
Hi,
I'm trying to load the secure_debug bootloader for the nrf52 with the SD 132 3.0 and an aplication.
But when I load the aplication the bootloader gets erased or overwritten...
I've got a problem to change polling method to interrupt notification on open-mesh with freertos project.
The example "BLE_Gateway" of open-mesh as flow:
if (rbc_mesh_event_get...
Hi i have to use this accelerometer and connect it through i2c
www.analog.com/.../EVAL-ADXL345Z.pdf
This is my connection:
VIO --> 3.3V
GND --> GND
CS --> 3.3V...
I am using nRF51822 and the Software device is S130. The application is based on ble_uart_app. I can declare it as a Bluetooth 4.2 device for lab approval. Right?
