I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi,
The spi_config structure zephyr provides is as below: Wherein cs is initialized to the chip select pin. In my project I have a requirement to handle 2 slaves which...
There is a bug in the sample/nrf9160/at_monitor, namely to do with +CEREG unsolicited notification handler called "cereg_mon". "cereg_mon" expects 0-2 +CEREG status code,...
I'm trying to replace a RS232 cable with a BLE bridge with the Nordic Uart Service.
One nRF52832 configured as central (app_uart_example_central) and an other one as peripheral...
Hello,
We are working on a product that contains nRF51822. The product sends continuous data (2 bytes) via NUS service to the mobile app at a frequency of 200ms.
When...
Hello,
I am aware that this is not an Arduino support forum, but if I'm not violating any rules, I'd like to ask a question in hope that someone might have provide a helpful...
I'm developing on an iMac M1.
Over 2 month I tried to get the nRF Connect for desktop (V3.9.3) running on my M1-mac, without success.
Toolchain manager (v0.10.3) works...
Hi Nordic Team,
Currently we are exploring nRF52840 DK.
We have observed BLE Enable SOC usually have two cores, one as an application and one as BLE Soft Device core....
Hi - I am using the /nrf/samples/matter/lock sample as a reference template to develop my own app. Thank you for providing it!
I am able to build and flash the basic build...
After updating the firmware on NRF9160 Connect DK (using mfw_nrf9160_1.3.1.zip as well as the ltem asset tracker hex file) LED 3 does not turn on and AT commands in LTE Link...
I am using a mac M1, running macOS 12.0.1 Monterey.
J-Link Software and Documentation Pack v7.62 (latest)
NRF Connect for Desktop v3.10.0 (latest)
Programmer v2.3.1...
Hello,
i'm using a nrf52832 dk and i'm using the example ble app uart.
I saw the packets that are send for rx or tx but with packets of 20 bytes
I saw this post, https...
Hi,
I have some problem with NRF52840. When I use software example "ram_retention" in peripheral directory on 2 différents board I have 2 differents state of VBUS pin. ...
Hello,
I am relatively new to iOS development and have now made the iOS version of the nRF Toolbox from the Github. After some initial difficulties, I was able to get the...
Hi,
I have a peripheral device that running on nrf5340 and can be updated via MCUMGR SMP. i tested it via Device Manager application and it is working.
My question is...
