We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
We are thinking to evaluate both the U.FL and Trace Antenna options on a custom nRF52840 prototype board.
1. Referring to this discussion, point 3 is about provisioning...
I want to use mesh configuration ( Bluetooth mesh submodule) to save data to the flash memory of nRF52840. The code works fine and I can save data to flash using mesh_config_entry_set...
Hi, I'm having problems with compiling the gazell_dynamic_pairing example with arm-gcc compiler for nRF52840 Dongle. I have already migrated other gazell and esb examples...
Hi,
I have this generic register read function to handle communicating with my sensor, and during initialisation, it works fine. However, when I try and request a transfer...
Hi! I'm trying to setup mesh network and get data from sensors thought SensorClient SensorServer via ProvisionerNode.
My Nodes info: - Provisioner, UnicastAddress 0x0001...
Hi,
I'm using DSK 17.0.2 on the nRF52840 DK.
I followed the instructions for a buttonless serial DFU:
1. I cleared my board (nrfjprog -f nrf52 --recover)
2. flashed...
Now I meet a problem: when the chip of nRF52832 is power off, but supplies power to one GPIO pin of the chip through resistor voltage division, then I found the voltage of...
Hi everyone,
I'm currently trying to the get UART logging running on the NRF52832, but fail to get the SDK working.
My settings are as follows:
#define NRFX_UARTE_ENABLED...
I want to use GPIOTE implement soft uart on nrf9160 Because it can use interrupt to receiver and data
Any kind man give a example here. that will be thanks a lot
Hi all,
I new to Nordic Semi and recently got started with nRF9160-DK. I've gone through the getting started guide and am looking for suitable tutorials, and examples to...
Hello,
I wanted to show a colleague all the great features that the Cat Tracker has. I am working with Settings. The most important feature exists -- when I change a setting...
I'm working with SDK Release 1.5.1 and Toolchain Version 1.5.1
I'm trying to configure the serlal_lte_modem example to support the HTTPC feature and switch to UART_2 for...
I added the following code to FDS:
It seems sometimes this works fine, and after GC is complete all record headers are valid. However, sometimes it doesn't, and dirty...
I was following the tutorial and extracted with the git instruction into my SDK 17.0.2 at the following path C:\nRF5_SDK_17.0.2_d674dde\examples\peripheral. When I attempt...
