I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi all,
We are running into a problem with our battery powered nRF52.
The nRF is continuously powered by one lithium cell. When the battery is very deeply discharged ...
Hello,
In our current design, our boards use P0.18 connected to an external watchdog to reset the nRF52840. We configure PSETRESET[0]/[1] to be 0x12 (Connected/enabled on...
Hi,
I am using Zephyr to do some action in a main loop and ksleep for 30 seconds. While in ksleep(), I can see that the consumption is 20ua. The board is a very small simple...
I have a Fanstel Evaluation board which can be programmed through 52 DK board, no problem there and i also have built a custom board using the BM833AF modules based nRF52811...
Hi,
I was wanting to know if this function has been changed since mesh SDK v2.2.1? It appears to not behave quite the same. When I call it, I think the mesh does not entirely...
I am currently working on sending some custom data using BLE nrf52.
I find the BPS format best suited for my application but I want to modify the systolic and diastolic...
I am adding dfu capabilities to my app on SDK12.3.
For that, I took the example on sdk12.3/examples/ble_peripheral/experimental_ble_app_buttonless_dfu and copied the relevant...
I am trying to modify the receiver an transmitter examples to change the default bandwidth on both the receiver and transmitter. I have looked through documentation without...
What is the communication distance of NRF52832 Bluetooth reference? Since nrF52832 is used for the first time, we are not sure about its performance. Is it possible to reach...
Dear Team,
I am try to customize the some of the parameter of HTS221 temperature and humidity sensor used in thingy52 board, However if I change any of the parameter then...
I am using the nrf connect desktop application on windows with a PCA10059, and have found the application to be buggy when receiving a flood of notifications, this works fine...
I've been logged in for about a week now, and still can't log out.
I left a posting about that almost a week ago with some "bumps" later on the "back stage" section, but...
Hi!
Can anyone tell me that isthere any app which logs data automatically into txt or csv file from nrf52???
I am getting data at nrf connect but every time i need to...
PCB : thickness 1 t(1mn), 1/2oz, 2 layer
The antenna was removed and the VNA was connected between L3 and C6.
The impedance was about 100 ohms.
The part value is shown...
We have a latest set of prototypes which use an NRF52840 on a Laird BL654 module.
On two of these protoypes the module is unresponsive. We are using a J-Link Lite module...
