hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Community Members,
I have a nRF51822 SoC custom board on which i have successfully tried flashing the executable file using openocd commands over Linux environment...
After the rewrite of persistent storage in SDK For Mesh v4.0.0 the code no longer does any basic sanity checks on the data read back from the flash.
The code below is from...
Hi
I am evaluating the serial_lte_modem sample with pc as client but failed, could you share the cmd format for gps start function?
here is the log after I issued the...
Hi guys, I'm facing the next problem:
I am using the Android BLE Library and Android-nRF-Mesh libraries. I connect my Android application to 8 nodes. One of those nodes...
To perform dfu using nrfutil, we need to bring wpantund service down in order to provide serial port to nrfutil. That restrict me to communicate with end nodes. Can you please...
Hi Nordic people,
According to my knowledge SPI can not verify the bits whether it is properly sending or not(like ack),speed wise is SPI ok,And in nordic nRF52840 have...
Hi!
I'm trying to use the LIS2DH12 driver on SDK 16.0.0 in SES. I've managed to read the correct value of who am i register. I'm trying to configure the sensor using LIS2DH12_DATA_CFG...
I have set up 2 nrf52 dev kits: one central and one peripheral. The peripheral side hits the PM_EVT_CONN_SEC_FAILED event about 30 seconds after the connection was established...
I'm trying every permutation.
Pressing IF BOOT/RESET button along with BUTTON 4 and powering off and on the board ... then letting the buttons go
There is a reset...
Hello,
it would seem that the Spi Slave example provided with the SDK 12.3.0 does not work correctly for the nRF51DK. Setup:
Master SPI : STM30G070CB Slave SPI : nF51DK...
Good day,
I have a problem with a custom board I have designed. It does not advertise the BLE device when programmed. I am testing with the simple ble_blinky and the nrf_connect...
I have nrf52840 development boards, when I ran DFU example (from NRF SDK for thread and zigbee v4.0.0) on autocommissioning true on 2 boards and was able to run it successfully...
Hi,
Is there any way to disconnect the NRF Toolbox connection through code. I tried to do the same but once ble turns back on its connecting back to NRF toolbox.
Hello,
I'm using (nRF 52840)Laird BL654 Module. I want to test PA/LNA Features Without a Soft device. please Suggest me how to test.
Regard's
-Nikunj Patel
Hello, I come from China, there is a new thingy:91 board,I had set bluetooth gateways,added sim card,added a device nrf-352656100749665 , update certificates and the modem...
