Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I am using nrf52840 mesh v17.0.2 light_lightness server example.
In the original Light lightness server code, you can control LED1 using J-Link RTT Viewer. By sending...
I need my own input handler procedure that cannot wait.
Interrupt handler is directly attached as GPIOTE_IRQHandler (i don't use your libraries) and takes no more than two...
I am new to Nordic. I installed nRF Desptop Connector. I have opened succesfully the sample nRF projects. Now, I want create my own new nRF Connect Project. I tried two ways...
Hi,
I'm trying to set up a custom driver for the VL53L1X Sensor. (nRF9160 + Icarus Board + NCS 1.7.1)
I placed a new folder in drivers/sensor + modify CmakeLists.fr &...
Hi,
Our project team has decided not to using an external MCU to interface with the 9160 over the UART. So we'll need to write our application on nrf9160. The application...
P19 (Debug OUT Connector) on the nRF52840 BLE RF Development Board, PCA10056 (Dev Board) provides the ability to program a nRF52840 BLE board (BLE Board).
Questions:
...
Hi there,
Attempting to use the sample program for direction finding and have been following Case ID: 280319. Have attempted to add the code suggested by Simonr in adding...
Hi,
I'm working on a project using Zephyr and ncs 1.7.1. One of its functions is to stream WAV files from a SD card. It only ever reads data.
The issue I'm having is...
Hi all,
I am using SES in Win10. After I updated my NCS to 1.7.1, I failed to open my solution. However, it runs succussfully in SDK 1.6.1. The infomation is below:
...
Hello.
I am currently working on implementing a PWM control function using nrf52840. I used the function "es_battery_voltage_get()" to read the battery voltage before and...
I have written simple hello world code on nRF9160 custom board and enables the MCUBoot as bootloader using CONFIG_BOOTLOADER_MCUBOOT=y in prj.conf file.
Also, made some...
Hi everyone, I'm trying to communicate with OBDII through NUS using nRF52832. I was able to initiate the connection, send commands to OBDII, and get responses on the ECUsim...
The current RRC Inactivity Timer from my provider is 10 seconds, causing my power consumption in RRC Connected mode to be unnecessarily high.
I want to use the Release Assistance...
Hi,
Can anyone check if my understanding about this NFC-BLE pairing feature is correct?
1.Before connecting, two BLE devices will exchange some keys or info for secure...
