VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
I am trying to create an AOA link sending a CTE from an nrf52811 (BM833A module) and the receiver with an nrf52833 (bl653 module). Analyzing the CTE detection data, the first...
Hello guys,
I've a PCA10040 connected to my laptop.
It works fine with all the .hex BLE template example in the nordic SDK except with the UART example.
After download...
Hello,
I was using the usbd_ble_uart code for the nrf52840 dongle. When I connected the dongle to u-link 2 debugger and used keil uVision I was just doing my settings in...
NCS version：v1.5.1
board：nRF5340DK(0.11.0)
first，i use SES Embedded open radio_test project and choose nrf5340dk_nrf5340_cpunet ,and use [west flash --erase] download...
I am using nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using MacOS and nRF Connect SDK v1.6.1 .
a. The JlinkExe executes but JLinkRTTClientExe doesn't show any...
As noted in recent past cases, we have an issue with the state of the nRESET pin that is causing unwanted resets when connected/disconnected from external hardware (programmer...
I used NRF52840 Base on NRF SDK15.3 and freertos.
I have two task call nrf_crypto_aes_crypt a t the same time occasionally return NRF_ERROR_CRYPTO_BUSY. And also I add mutex...
Hi
I am developing with nrf52832 development board and sdk17. I'm trying to communicate with redpine rs9116w through spi but get some problems.
I have an other nrf52840...
Hi,
I'm a beginner at this, I'm a software developer so I've never worked with hardware but now I need to and I don't seem to be able to make it work.
I would need help...
Hi,
I have nRF9160 Power Measurement DK board, (PCA63511 Rev 1.1.0). And
nRF52 dev boards (nRF52840) (PCA10056)
I measured my program as: with nRFConnect version 3.2...
I have a project I have been working on for a touch switch using the nRF52840. I have been developing it using NRF Connect 1.6.0 and testing it on the nRF52840DK board. It...
I have some code handling the `BLE_EVT_USER_MEM_REQUEST` event. When I try and call `sd_ble_user_mem_reply` from within that handler, It is returning `NRF_ERROR_INVALID_STATE...
Hi,
My application has several characteristics that require read/write authorization. But for some peer I only want them to have access to some certain characteristics...
Hi,
I have a custom board based on the PCA10015 where im not getting any contact between the NRF9160 and the IBASIS SIM.
The SIM is in the correct way and i have the same...
