void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello,
Project Description
in our project we have multiple nRF52DK and one nRF52840DK. We are using the SAADC on the nRF52DK. The SAADC is configured with 4 inputs in...
Sorry in advance for the length and possible irrelevance of some of what I have written here
So I am trying to figure out how the ble software works. I have the ble_app_blinky...
Hi , a few questions related to using XRFTEST command in burst transmit mode:
1. Having looked at 9160 AT command manual and TS 36.521-1 Table A.2.4-1 where the NB-IoT reference...
Hi,
I found I APPCPU3 is 0.3mA higher than I APPCPU5 . I have no idea. How come CPU consumes more power utilizing HFXO64M, an external oscillator 64MHz, than utilizing a...
Hi all,
I would like to check and see if its viable to keep radio on TX_ENABLE throughout the radio's operation, ie keeping TXEN = 1 ; at all times or keeping radio only...
hello,
i find a mistake line 62
"ldr r0, =%4 \n" ->>>>> The '=' should be removed .
void app_error_handler(ret_code_t error_code, uint32_t line_num, const uint8_t...
modem fw 1.3.0
ncs 1.5.0 and master
I am trying to test modem firmware upgrades using the lwm2m client sample and every time it is writing the 20% downloaded chunk, the...
Hi, I am following the tutorial and have some questions during the implementation.
devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-2-ncs-v1-4-0
A red led...
Hello There,
So basically I need to send and receive and data from to Serial Terminal via FTDI module to nRF9160 DK. So for this I am using ncs\v1.5.1\nrf\samples\peripheral...
Hi.
After updating Programmer of nrfConnect to v1.4.9, I have not be able to "execute Erase All" command.
Error message is "Error: Error occured when program. Errorcode...
Dear Nordic,
how to set UART/USB console output to be non-blocking? We use printk() to output some debug info to USB console. When the USB isn't connected, the program stalls...
Dear Nordic-Support-Team,
I (software developer) work together with an electrical engineer to develop a device, which will incorporate the nRF9160 SiP. The firmware/application...
