Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello everyone. I want to turn the LED on and off with the push button, if I want to hold it down after 3 seconds the LED will turn off, if it has been pressed for less than...
Hello
I am trying to port a custom project for nRF52840 from Keil to Segger Embedded Studio -uVision V5.33.0.0 -Armcc V5.06 update 7 (960) -SDK 15.2.0 -Device Familly...
SDK version: SDK17.0
We have low received radio message count with open USB CDC compared to when it is closed.
The low rx varies from 20% to 50%.
USB open = screen...
Hello!
what command should I send via BLE to disable the pressure, gas, and light/color intensity sensor?
In this documentation: nordicsemiconductor.github.io/.../firmware_architecture...
Hello
Assuming I set FDS_CRC_CHECK_ON_WRITE flag in sdk_config to 1, where do i get a notification that somthing went rong? I probably miss something but I need to clarify...
I'm using nRF52 DK BLE.
In the code, I used the following code to set the Tx Power = +4dBm.
On my HUAWEI Android phone, I use the nRF Connect app to see the RSSI. My...
To test the example, I downloaded the project through the following path.
https://github.com/NordicPlayground/nRF52-ADC-examples
I get an error like an image. What should...
Hi!
Hope you are doing well!
I am developing a BLE device and right now I want the device be able to auto reconnect to the phone.
e.g. The user leave home with...
Hello
SDK = ver 17
DK = nRF52
Using Peer manager for writing peer data in flash and FDS to store app settings in flash.
1. They both share the same spcase in flash...
Hi,
We are in the middle of product certification, right now with BT SIG testing. Unfortunately we got stuck right away since the test house cant configure the device...
NRF52832
SDK 17.0.2
SoftDevice 132
I am connecting with telnet to an exposed RTT port to see the logs. I adjusted sdk_config.h to use RTT instead of UART logging. The...
Question 1:
The nRF9160 datasheet V2.0 claims the sensitivity is: CATM=-108dBm (mid band); NBIOT=-114dBm (mid band).
However when the unit connects, we get a printout...
So in the MQTT example the following function is used to write the CA certificate to the modem so a TLS connection can be setup.
In our code/TLS setup we want to use Client...
