Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello,
I am using a custom nRF52840 (SDK 14.2.0, SoftDevice S140) based board.
Our boards stopped advertising and upon debugging we saw an error in the peer_manager_init...
I am testing the product's DFU using nRF52832.
Select File disappears after downloading nRF ToolBox App once.
Is there any way to not disappear from nRF ToolBox?
If...
Can I use P0.21 as a regular GPIO ? When I power the chip up, will it start correctly ? Is there any problem if I connect it to a LED and resistor ? How do I configure this...
I'm using the NRF52840 SDK 15.0.0
I have 2 task threads and 5 ble services.
Now what happens is when I'm trying to connect the device with 2 tasks and ble services I'm...
Hello,
Is it possible to read the received byte if the parity error occurs? Because I want to receive 9-bit data on UART and get the 9-th bit based of error?
Dear
I am trying to locate the data area of application code from device (nRF52840).
From here , it show me the bootloader will locate at from 0x000 F 8000 – 0x000F E000...
I've been writing a vendor model for Bluetooth mesh based on the light lightness model in the SDK. I'm extending the generic level model into my model - a window openess level...
Hello -
I am trying to set up the nRF9160 DK kit. I successfully updated the firmware and entered the ICCID, PUK, IMEI, and HWID values. When registering for nRF Cloud,...
Howdy,
I'm trying to get Zypher up and running with the Particle Argon board using the nRF52840 chipset. The goal is to get both Bluetooth and UART working, but for now...
Hi all,
We are using nrf52 DK (both pca10040 and 10056) to develop a multi-channel ADC sampling module running Mynewt.
The example ADC code with Mynewt is a single-channel...
Hi All,
I am in the process of fabricating my own PCB for the first time using nRF52840 chip.
The design will be somewhat similar to the nRF52840 Dongle design with slight...
Hi All,
I am trying to simulate the nRF52840 Dongle Antenna given in the hardware files using CST studio. I am using the following substrate and trace width which was in...
Hi All,
I am trying to write a driver for the Grove-LCD RGB Back-light V4.0 using nRF52840 DK. However, it doesn't work. I am trying to figure it out why.
The description...
Hello, I'm a beginner who just entered Nordic.
It may be difficult to read because I am not good at English. Please excuse me.
I use NRF52DK and SDK v17, and I'm developing...
Hi guys. I'm currently stumped by a most peculiar issue.
Im using two PCA10040 boards (20 cm apart) to send a data stream via the GZLL protocol: DEVICE button pressed -...
