I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi, in our project we use nRF5340 to control some externanal peripherals as flash mem through SPI and also we need BLE comunication.
The case is if whe allow the config...
Hi, I am trying to use the DECT NR+ sample from the 2.7.0 nrfconnect sdk but I can't seem to get the following to work in the prj.conf:
the results of my build give...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
Hello,
I'm using "Bluetooth Mesh Light switch" code which i have modified to act as a gateway. Where it periodically collects data from lights. After receiving data from...
Can the VDD PIN of 4L15 be used to detect the ADC voltage? VDD is powered by a dry battery (3.2V~1.8V), LED+ is powered by 3.3V, LED- will be connected to the I/O of the 54L15...
Hi,
I would like to add MCU boot hardware downgrade prevention in my project.
So i had the following config in prj.conf
Then, when i flash my board i get this error...
I am trying to configure himax camera and stream to app but unable to get image, rather when I am using nrf app to see data i am getting data something like this:
'40-13...
I saw a few questions related to this but nothing I found quite answered my question. We are experimenting with the nRF9161 DK, and we need to securely identify which device...
Hi there, right now I'm working with an application that allows me to collect data via UART from several sensors (two), and I also I have a SIM module that allows me to communicate...
Hi,
I'm trying to build the " tx_rx_non_blocking " sample (ncs2.70, nRF52840dk) but get the following error message -
C:/devtools/nordic/ncs/v2.7.0/modules/hal/nordic...
The CPU runs the main thread every 3 seconds, and for the remaining time, it enters the idle thread. However, after entering the idle thread, it doesn’t save power.
But...
Hi guys,
we are planing to use the nRF52820 as BLE proxy to UART/SPI. It shall receive data from a host controller via UART/SPI and forward it via BLE to a smart phone....
I recently purchased an nRF52840 DK (v3.0.0) to use with my custom nRF9160 boards for firmware loading, debugging, and loading certificates for nRF Cloud. While I can successfully...
