VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
I'm currently looking for a high-speed data transmission and reception solution that requires wifi (NRF7002) throughput, but I don't want to transmit data via wifi. It should...
I'm using nRF Connect for Visual Studio Code, working on a project that has worked great in the past, but I'm getting error messages now when attempting to flash any board...
Hi,
We are using the PMIC in our smart ring where we have limitations of number of components used and specially the height of the components used. Here, the inductor...
Dear Nordic Support Team,
Hope this email finds you well. I am currently developing a Matter-enabled device using the Nordic nRF Connect SDK, and I’ve encountered a question...
Hi,
I just got a power profiler kit II and I want to use it in an battery based application, where there is also the possibility that current will flow in the opposite direction...
I am using the nRF54L10 chip with NSC-V3.0.0, and I encounter an issue when using uart21 (p2.07–p2.08). If RTT is connected, UART transmission and reception both work normally...
Why doesn't the scan_evt_handler get called in the ble_app_uart_c sample under nRF5_SDK_17.0.2_d674dde conditions? I've tried various things, but neither scan_evt_handler...
Hi,
We are testing a custom board based on the nRF5340 that drives an RGB LED strip using the TI TLC5947 LED driver.
The TLC5947 has an OE (Blank) pin that disables/enables...
Hello,
I am using an nRF52833 in a project where and i want to be able to update it via another mcu (STM32H7) over uart. The STM32 has received and saved the new hex file...
Hi, I have a custom NRF52840 board that I need to send EMG data via BLE with. Only has SWD, no usb-c data link unfortunately.
I am using version 1.6.1 of Adafruit NRF52...
I was reading the Errata document for the NRF54L15, and came across this: 3.18 [37] POWER: Current consumption might increase after pin reset or power cycle. So I was wondering...
I'm testing the NRF54L15 radio and found an issue. When I set the radio to BLE 2Mbps mode, I received data from adjacent frequency bands. For example, I set the radio's receive...
