void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hello, I am new to Nordic, I was previously using Cypress CYBT343026-01. But there were some drawbacks found during development. 1. It was consuming 315μA at 0 dBm BLE tx...
Perusing the GCC linker script supplied as part of SDK v16, I noticed that the .data section is specified as follows:
.data : AT (__etext) { __data_start__ = .; *(vtable...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
Hello
I'm going to use a potentiometer to control the pwm. I am using a 10K potentiometer and have used a saadc example.
I printed out the value of adc through this example...
Hi everyone,
I've just been working with NRF52833 and nRF5 SDK for Thread and Zigbee v4.1.0 to create a zigbee mesh network for home automation. My network is pretty simple...
Dear Members,
I saw this code ,
If there is no input, how can I handle it and display result = 0 and not shutting down CPU ?
How can I display 0 from this code...
Hi.
I want to disable the TWI master's internal pull-ups on SCL and SDA. So I set it according to the contents of the following URL, but the setting is not reflected as...
Dear Nordic Support team,
Currently I am in the process of adding the USBD_CDC_ACM driver code to our existing application following your usbd_ble_uart example. I can receive...
Hi，
Our customer is using nrf9160.There is a problem about powem_on circuit .
Attach is the schematic diagram:
Here VBAT is 4V,PW_ON is connecting to the nrf9160...
Hi,
I'm using nRF52810.
And i'm trying to measure battery level using saadc.
The problem is saadc result is not accuracy.
When battery voltage is 3.3v, saadc value...
Have a brand new Thingy 91, latest modem firmware and asset tracker firmware: thingy91_debug_ltem_2020-10-30_5522ca2b.hex.
But within the LTE monitor app, nothing shows...
For the nRF52811 there is only one TWI peripheral and if there are multiple buses required it is necessary to remap the SCL and SDA pins to the peripheral. In the nRF5 SDK...
I am migrating to the Fanstel BT840XE module with nRF52840 and a Skyworks PA/LNA. I need some assistance in getting my PA/LNA working in a multiprotocol setup.
I have successfully...
