NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
Hi
I'm a total beginner here and I have the gyroscope sensor LSM6DS3 and I have the nRF52 DK
I want to read the sensor's data via I2C (i.e. using SDA and SCL pins) using...
Hello.
This is becoming a very serious issue for me. When I program the nrf52840 dongle and when I switches on the power, it automatically goes into bootloader mode, means...
I purchased a sparkfun breakout board ( https://learn.sparkfun.com/tutorials/nrf52832-breakout-board-hookup-guide and schematic https://cdn.sparkfun.com/assets/learn_tutorials...
I'm compiling a custom application using the CMake scripts in the nRF mesh SDK. When I debug the application, even though the debugger is working – I can pause execution ...
I am trying to modify the central / peripheral relay example to not use the HRM and RSCS services and to use my own custom service instead.
I am following this tutorial...
Hi
I have the nRF52 Development kit and I can program it using SEGGER Embedded Studio IDE without problems. However, when I try to program it using nrfjprog, the Dk doesn...
Hi to all, I'm developing a new device that should be a multiprotocol: Zigbee (as coordinator) and BLE peripheral (with his own GATT) There is an example for this integration...
I asked a question on here couple of days ago, but I resolved that issue and have stumbled into a more concise and in the right direction. I am using ble_app_uart as my code...
I am using ble_app_uart as my code base. I included FDS.c and FDS.h when I compiled, it presented many config errors. I compared the two config files for the FDS example and...
Hi,
I have some problem about Keil hex output file.
At the end of hex file, there have some line as following image.
In (a) of above image, why "hex file" need to...
Hello again Nordic Pro's,
This is a quick question that I have not been able to find the answer for before buying nRF52840 dongles to replace our nRF51 dongles. We need...
When attempting to initiate GPIOTE pins, I get an NRF_ERROR_NO_MEM on the 5th pin. I saw reference to there being a maximum of 4 high accuracy channels but I am attempting...
Hello.
I want to use the CMSIS configuration wizard.
It is work in the example but not in my project.
From looking at youtube I found what I need to add to tool.xml...
Dear Team,
in Feb 2019 this link was available: https://www.nordicsemi.com/DocLib/Content/Product_Spec/ nRF9160 /latest/ref_circuitry?932#concept_myt_5zt_bgb
with the...
