Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hello
in the zephyr 1.7 release there have NRF52 and NRF51 porting without softdevice .
in the SDK 13 ,there has Freertos example working softdevice ,is there any plan...
hello friends :)
i'm trying to make an nRf51822 evaluation board for breadboard
i used 0.1" header and power from usb connector
i'll upload my altium schematic and...
Hi,
We are doing DFU updates through a nrf51422 dongle (data passing from UART to BLE), using our own code, based on the multilink central example.
The DFU peripherals...
Hi, I'm have a question :
If i download s120 or s130 softdevice, which SDK version i need to download ?
Which version is compatible with my nrf51822xaa ?
The reason is...
Our BLE hardware is designed to send data at 50 Hz speed continuously using nrf51822.
It worked well with APP with Android 4.3 and some Android 5.0/6.0 ,we can receive data...
Hi,
I'm getting familiar with my nRF52 DK (PCA 10040).
I stumbled on something when I was doing an application that toggles LED1 on every TIMER0 event (200ms). Here...
Hi,
Id like to understand the FDS state after flashing the device. Im trying to check if the record exists then I use it, otherwise I write a valid info into the record....
Hello All
Could you please guide me. i want implement BLE with SPI interface...if i sent any command via mobile Bluetooth..then NRF51 DK should receive the Command and...
I have already changed the define NRF52, NRF52832_XXAA,BOARD_PCA10040 to NRF51,NRF51822 and BOARD_PCA10001 and adjusted the ROM and RAM areas as below.
But there...
ERROR OCCURS WHEN TESTING UART nus service on a nrf52832 custom board UART APP SHOWS LIKE THIS device doesn't support UART WHEN I TRYING TO CONNECT WITH MY DEVICE. PLZZ H...
Hi Nordic Team,
In one of our application, we need to interface BT HCI chip with Host MCU(Cortex M4 based). Below are the application profiles we need support for:
...
I am having trouble using GPIO P0_9 and P0_10 as GPIO pins. These are the pins designated as NFC1 and NFC2.
I am using the following sample code:
#include <stdbool.h...
Can a peripheral device know when the client made a scan response request? I want to use scan response as a form of acknowledgment so the peripheral device knows that the...
