I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
We are using NRF52840PDK for development using NRF Connect SDK. We are facing an unusual behavior while using PDK. The development environment is Windows 10 and SES5.60 installed...
Hi,
we are trying to send data (a packet of 54 bytes) at 100Hz but our data is not always transmitting regularly.
Much of the time the TX is perfect but every so often...
Hi,
If i need to call zephyr driver API clock_control_off( ) present in zephyr\include\drivers\clock_control.h on LFCLK. How can I do it,.? As an example, to populate...
We have a RFID sensor reader part number RFM5114 , manufactured by Nordic , the sensors we use to read are RFM2100 Magnus S2 tag. Now we have to read sensors RFM2121 Magnus...
Hi everyone,
Is there a way of being able to view the contents of the advertising packets (advertising and scan response) without using a bluetooth sniffer? Is it possible...
Hello,
I made a code on NCS1.5.0. The main function is to realize audio encoding and decoding. It runs and tests normally on nRF5340 DK. When I migrated this code to NCS1...
Hi, While I'm aware that the specs are not yet finalized, are there already any hardware requirement estimates for running Matter over Thread for a battery powered node? I...
Is it possible to perform an over the air update via Bluetooth Low Energy while the sensor is connected, but the app is running in the background? If this is possible, are...
Hi,
I found that when my custom board spend 201 ms to boot up. Because I can't change my board, I am looking for reducing time to boot up.
Do you have any idea and how...
Can you please tell me why I get an -ENOTSUP error when I set the scan .timeout parameter to anything but 0? Is the suggested workaround to use RTOS functionality to timeout...
Hello All,
I have the following issue - a peripheral and a central using nrf52832 with SDK 15.3 and S132 - on the peripheral I advertise with a whitelist - the central scans...
nRF Connect used to work fine. After the 3.8 update it could no longer see devices. At that point a re-install helped.
Then after the 3.9 update it stopped working again...
Dear support,
I am using nRF52840DK (PCA10056) and nRF5 SDK version: nRF5_SDK_17.0.2_d674dde. I am trying to make all the prints in my application to be displayed properly...
I working with the MDBT42Q-DB with the nRF52805 module. I've started from the ble_app_beacon example in SDK 17.1.0. I was able to compile and run the example in Segger Studio...
