Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
I am in the conceptual stages of development for a BLE test system.
The test system requires:
Fast transceiver and connection with BLE devices, preferably capable...
I know Nordic is releasing the nrf9160 on the 12/12/2018, and from what little documentation I can find it doesn't seem to have BT or NFC hardware integrated. Are there any...
Hello, I have installed nRF Connect and the Programmer following https://infocenter.nordicsemi.com/pdf/nRF9160_DK_Getting_Started_Guide.pdf At step 3.2.2 i see "No devices...
Where can I find a drawing of the footprint for the nRF52840 WLSCP? Normally it would be near the end of the datasheet, after the mechanical drawing of the package. The datasheet...
I have an application running a serial communication through a RS485 interface. I have two sensors attached through I2C/TWi.
I have a app_timer that quwry the sensors once...
I have built on the CoAP example a POST request to the server. This works now without any problems.
I do send the received signal power within my POST. To get the power...
Hi,
I purchased a NRF9160 DK and am having problems on the first time I am trying to compile the SERIAL_LTE_MODEM application . I followed the steps according to the documentation...
Hello,
when I open any example Project from https://www.nordicsemi.com/Products/Development-software/nRF5-SDK with Keil MDK v5, I directly get the Error Message "Cannot...
Hello,
I'm a beginner of nrf5340, when I tried hci_pwr_ctrl(ncs v1.5.1) , I met some problems.I adjusted the tx power and changed prj.conf :
Then I added hci_rpmsg...
After updating nRF Connect and the Programmer app, DKs aren't being recognized when clicking on Select Device.
Tried both with nRF9160 and nRF5340 DKs and neither was detected...
I'm working with the PCA10040, the SDK V11.0.0. and the winbond memory flash W25Q80BV.
For the SPI connection I'm using the the SPI2 because TWI0 and TWI1 are being used...
Hello
First of all, I`ve been spending way to many hours trying to figure this out, so I decided to open this ticket. I am new to microcontrollers in general and the Nordic...
Hello:
I'm new on nrF52832 development. I did some tests using nRF51 and so far so good. However I received a few samples of E104-BT5032 from eByte http://ebyte.com/product...
Hi,
I have 2 SES projects that both require softdevice plus application.
One of the projects combines application and softdevice into the .hex file that is generated...
