Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi there!
I'm having an issue adding WiFi functionality to my project. I use the nRF9160DK and the nRF Connect SDK v1.5.1 on a Windows10 platform.
To keep it simple i...
I am using nrf52DK board as an observer to test my beacons. I have kept scanning enabled all the time (scanning interval & scanning window same), but the scan_evt_handler...
I want to use the nrf5x to develop the host/gateway of bluetooth mesh, may I ask which model is more suitable, which model currently supports the most mesh nodes?
And which...
Hi Nordic team,
I have successfully developed an application using nrfx (Timer/PPI/SAADC) combo in NCS 1.5.x to be able to sample 2x differential channels very fast.
Similar...
I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I have a device that uses a custom BLE service, And when using nRF Connect on the mobile phone, all...
I have been developing some nrf52832 code (SDK 17.0.2) using the Segger RTT debug window for logging. I added the code from the UART example but the printf goes to the debug...
I'm planning to modify the nrf52832_ciaa reference designs in altium to emulate the functionality from a development kit and add an RTC.
I need access to pins P0.23, P0...
Hello. I would like to use an internal RTC to keep time going even if the power is off.
1. Is it possible to implement with 'nrf_calendar' module?
2. Should I think about...
I have a battery powered iOT device using BLE, I2C, and GPIO. I am focused on reducing the power consumption. When BLE is not connected, I want to have as little power usage...
This is in response to a central sending an update. I try and follow with the central's request except I set the times to the AUTO value. If I get an NRF_ERROR_NOT_SUPPORTED...
ran nordic blinky example on nrf52840 kit
Want to know where is the transmitter power set in the code.
refer any example where we can define transmit power
Hi Folks,
I am just asking general information (explanation and/or code samples examples) to set up a secured BLE connection between multiple centrals towards one peripheral...
Hi,
I'm programming a nRF52832 for SPI communication with another device which requires some single byte TX/RX. After a lot of head-banging, I realized that the nRF52 was...
Hello there,
if i download a hex-file to the NRF52840-Dongle with the J-Link (Lite) tool, the dongle always remains in bootloader mode (red led is flashing). But if i download...
