It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
I have installed CMSIS according to this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v14.1.0%2Fsdk_config.html
documentation. After...
Hi Team,
One of my application needs the UART driver in both Interrupt and DMA mode for more data bytes transfer. No need of timeout operation or polling mode.
Can any...
Hello Nordic;
I use SDK 17.0.2 and gls example . We know for security in pairing, considered a password which that is randomly generated in SoftDevice and sent to UART....
I am having problems loading an existing project that I successfully built and ran in the past.
I open IDE from nRF Connect > Toolchain Manager > Open IDE
The SES opens...
Hi,
Our Nordic app is doing BLE<->SPI communication.
All works fine when running in debug mode with SEGGER IDE.
Once we run without the debugger running, the SPI transmits...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
Hi,
I'm using nrf52840 on a custom board and have a sensor connected over the pins P0.9 and P0.10
which are NFC pins that have been converted to GPIO by using macro (CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
which hex file shall i install for an LTE application ?
It is basically step 7 of this tutorial: infocenter.nordicsemi.com/index.jsp
I wanna have a LTE application...
I am trying to start developing on my nRF52833 DK using Segger embedded studios, but my board does not show up as a mounted device on my laptop (echoed by the fact that Segger...
Hi there.
I am attempting to do some reallife tests on the nrf52840, mainly focusing on long-range capabilities and performance between the DK and an iPhone XS. Are there...
Hello, I've seen several posts about this, but I'm a little hesitant to use older posts since you guys put out new and improved versions pretty quickly. We are using SDK 16...
nRF52832 on a nRF52DK connectivity_4.1.1_1m_with_s132_5.1.0.hex pc_ble_driver_py v0.14.2
Steps to reproduce: - connect to a peer device - discover services and attributes...
hello :
1)The packet format of NRF52832 2.4G is as follows, I would like to ask whether the 2.4G CRC can be turned off.
I use two boards PTX and PRX to transmit each...
Hello fellow developers,
I'm developing the Bluetooth Low Energy (BLE) app with my own functions. Now I would like to pack it as a standalone Electron App, which can be...
