void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I have an application that does HTTP requests to a backend server. I'm now working on implementing TLS for encryption of the data.
Are there any examples of doing...
Hello everyone,
we are developing a bluetooth application based on the relay example included in SDK 14.0.0. We have already developed our own services and characteristics...
Hi,
I've been searching for a LSM9DS1 driver compatible with the nRF5 SDK >= 14.0 but I couldn't find any which uses the nrf_drv_twi so I started to write my own but it...
Hi All,
I'm working on minimizing power when transmitting a small message between two nRF52832 boards. I'm also trying to maximize range so sensitivity is important.
I...
Please ignore, this is test post. The SES project in Thingy:52 SDK seems to be broken, I get a lot of error trying to compile. What can I do to fix it?
Hello,
I have an application that requires an always running ADC to sample three channels at 4096 Hz. I have successfully adapted my application from the many examples posted...
I am working on Flashing Code into Nordic nRF52832 using SWD Protocol.
We have achieved 80% SWD in communicating and flashed code into Nordic and verified all is working...
I would like to confirm what I'm seeing on my setup trying to measure current with the nRF9160 DK.
I'm using an oscilloscope and am following the instructions in the latest...
If I were to design a product using nRF52840 & Thread. Normally, I would have to certify the product with the thread group and become a member. The thing is: - the product...
Hello,
I am developing a remote device which uses system off mode for idle state. I also have the condition where extra long press of any key that is beyond the long press...
My Peripheral is using the ble_conn_params module. I'm seeing that if my Peripheral calls sd_ble_gap_disconnect() soon after making a connection, the module will sometimes...
To the kind attention of Nordic support team,
I'm studying documentation in https://developer.nordicsemi.com/nRF5_SDK/nRF51_SDK_v5.x.x/doc/5.2.0/html/a00140.html where it...
Recently I check back again into att_mtu_throughput example in SDK 15.2. there seems to have some updates than in previous SDK, and I see this BLE_GATT_EVT_DATA_LENGTH is...
Dear all,
I am using the following peripherals in our product.
1. TWI Sensor
2. BLE
3. APP timer (1. to poll a gpio pin & as RTC)
4. SPI flash
5. 2 Edge sensitive...
